-
Je něco špatně v tomto záznamu ?
Plastination with silicone method S 10--monitoring and analysis causes of failure
M. Miklosová, V. Miklos
Jazyk angličtina Země Česko
Typ dokumentu časopisecké články
NLK
Directory of Open Access Journals
od 2001
Free Medical Journals
od 1998
ROAD: Directory of Open Access Scholarly Resources
od 2001
PubMed
15744385
DOI
10.5507/bp.2004.048
Knihovny.cz E-zdroje
- MeSH
- histologické techniky MeSH
- lidé MeSH
- ochrana biologická MeSH
- silikony MeSH
- zalévání tkání plastickou hmotou metody MeSH
- Check Tag
- lidé MeSH
- Publikační typ
- časopisecké články MeSH
Plastination is in some cases unsuccessful. The goal of this work was to monitor, to describe and to analyse the reasons of S10 plastination method failure. We prepared the silicone-impregnated specimens using the standard silicone method S 10. The causes of bad preparation are numerous. Usual defects produced during plastination process are the changes in the bulk, the changes in the colour and other visible defects (e.g. deformations, spots on the organs surface). The frequent reasons for these defects are: unsuitable temperature, using of old bad fixed formaldehyde specimens and too long gas-curing procedure. The knowledge of reasons of unsuccessful plastination is important condition for achievement the good results.
Citace poskytuje Crossref.org
- 000
- 00000naa a2200000 a 4500
- 001
- bmc13003804
- 003
- CZ-PrNML
- 005
- 20130220092622.0
- 007
- ta
- 008
- 130128s2004 xr o f 000 0|eng||
- 009
- AR
- 024 7_
- $a 10.5507/bp.2004.048 $2 doi
- 035 __
- $a (PubMed)15744385
- 040 __
- $a ABA008 $b cze $d ABA008 $e AACR2
- 041 0_
- $a eng
- 044 __
- $a xr
- 100 1_
- $a Miklošová, Mária. $7 xx0191265 $u Department of Anatomy, Medical Faculty, University of P. I. Safarík, Kosice, Slovak Republic
- 245 10
- $a Plastination with silicone method S 10--monitoring and analysis causes of failure / $c M. Miklosová, V. Miklos
- 520 9_
- $a Plastination is in some cases unsuccessful. The goal of this work was to monitor, to describe and to analyse the reasons of S10 plastination method failure. We prepared the silicone-impregnated specimens using the standard silicone method S 10. The causes of bad preparation are numerous. Usual defects produced during plastination process are the changes in the bulk, the changes in the colour and other visible defects (e.g. deformations, spots on the organs surface). The frequent reasons for these defects are: unsuitable temperature, using of old bad fixed formaldehyde specimens and too long gas-curing procedure. The knowledge of reasons of unsuccessful plastination is important condition for achievement the good results.
- 650 _2
- $a histologické techniky $7 D006652
- 650 _2
- $a lidé $7 D006801
- 650 _2
- $a zalévání tkání plastickou hmotou $x metody $7 D016613
- 650 _2
- $a ochrana biologická $7 D011309
- 650 _2
- $a silikony $7 D012828
- 655 _2
- $a časopisecké články $7 D016428
- 700 1_
- $a Mikloš, Vojtech. $7 _AN071340 $u Technical University, Kosice, Slovak Republic
- 773 0_
- $w MED00012606 $t Biomedical papers of the Medical Faculty of the University Palacký, Olomouc, Czech Republic $x 1213-8118 $g Roč. 148, č. 2 (2004), s. 237-238
- 910 __
- $a ABA008 $b A 1502 $c sign $y 3 $z 0
- 990 __
- $a 20130128 $b ABA008
- 991 __
- $a 20130220092813 $b ABA008
- 999 __
- $a ok $b bmc $g 966458 $s 801999
- BAS __
- $a 3
- BAS __
- $a PreBMC
- BMC __
- $a 2004 $b 148 $c 2 $d 237-238 $i 1213-8118 $m Biomedical papers of the Medical Faculty of the University Palacký, Olomouc Czech Republic $n Biomed. Pap. Fac. Med. Palacký Univ. Olomouc Czech Repub. (Print) $x MED00012606
- LZP __
- $b NLK138 $a Pubmed-20130128
