• Something wrong with this record ?

The effect of lubricant constituents on lubrication mechanisms in hip joint replacements

D. Nečas, M. Vrbka, F. Urban, I. Křupka, M. Hartl,

. 2015 ; 55 (-) : 295-307. [pub] 20151119

Language English Country Netherlands

Document type Journal Article, Research Support, Non-U.S. Gov't

The aim of the present paper is to provide a novel experimental approach enabling to assess the thickness of lubricant film within hip prostheses in meaning of the contribution of particular proteins. Thin film colorimetric interferometry was combined with fluorescent microscopy finding that a combination of optical methods can help to better understand the interfacial lubrication processes in hip replacements. The contact of metal femoral head against a glass disc was investigated under various operating conditions. As a test lubricant, the saline solution containing the albumin and γ-globulin in a concentration 2:1 was employed. Two different mean speeds were applied, 5.7 and 22mm/s, respectively. The measurements were carried out under pure rolling, partial negative and partial positive sliding conditions showing that kinematic conditions substantially affects the formation of protein film. Under pure rolling conditions, an increasing tendency of lubricant film independently on rolling speed was detected, while the total thickness of lubricant film can be attributed mainly to albumin. When the ball was faster than the disc (negative sliding), a very thin lubricant film was observed for lower speed with no significant effect of particular proteins. The increase in sliding speed led to the increase of film thickness mainly caused due to the presence of γ-globulin. On the contrary, when the disc was faster than the ball (positive sliding), the film formation was very complex and time dependent while both of the studied proteins have shown any qualitative change during the test, however the effect of albumin seems to be much more important. Since a very good agreement of the results was obtained, it can be concluded that the approach consisting of two optical methods can provide the fundamental information about the lubricant film formation in meaning of particular proteins while the simultaneous presence of other constituents in model synovial fluid.

References provided by Crossref.org

000      
00000naa a2200000 a 4500
001      
bmc16027865
003      
CZ-PrNML
005      
20170117104243.0
007      
ta
008      
161005s2015 ne f 000 0|eng||
009      
AR
024    7_
$a 10.1016/j.jmbbm.2015.11.006 $2 doi
024    7_
$a 10.1016/j.jmbbm.2015.11.006 $2 doi
035    __
$a (PubMed)26637935
040    __
$a ABA008 $b cze $d ABA008 $e AACR2
041    0_
$a eng
044    __
$a ne
100    1_
$a Nečas, David $u Faculty of Mechanical Engineering, Brno University of Technology, Czech Republic. Electronic address: necas@fme.vutbr.cz. $7 xx0209867
245    14
$a The effect of lubricant constituents on lubrication mechanisms in hip joint replacements / $c D. Nečas, M. Vrbka, F. Urban, I. Křupka, M. Hartl,
520    9_
$a The aim of the present paper is to provide a novel experimental approach enabling to assess the thickness of lubricant film within hip prostheses in meaning of the contribution of particular proteins. Thin film colorimetric interferometry was combined with fluorescent microscopy finding that a combination of optical methods can help to better understand the interfacial lubrication processes in hip replacements. The contact of metal femoral head against a glass disc was investigated under various operating conditions. As a test lubricant, the saline solution containing the albumin and γ-globulin in a concentration 2:1 was employed. Two different mean speeds were applied, 5.7 and 22mm/s, respectively. The measurements were carried out under pure rolling, partial negative and partial positive sliding conditions showing that kinematic conditions substantially affects the formation of protein film. Under pure rolling conditions, an increasing tendency of lubricant film independently on rolling speed was detected, while the total thickness of lubricant film can be attributed mainly to albumin. When the ball was faster than the disc (negative sliding), a very thin lubricant film was observed for lower speed with no significant effect of particular proteins. The increase in sliding speed led to the increase of film thickness mainly caused due to the presence of γ-globulin. On the contrary, when the disc was faster than the ball (positive sliding), the film formation was very complex and time dependent while both of the studied proteins have shown any qualitative change during the test, however the effect of albumin seems to be much more important. Since a very good agreement of the results was obtained, it can be concluded that the approach consisting of two optical methods can provide the fundamental information about the lubricant film formation in meaning of particular proteins while the simultaneous presence of other constituents in model synovial fluid.
650    _2
$a albuminy $x chemie $7 D000418
650    12
$a náhrada kyčelního kloubu $7 D019644
650    _2
$a lubrikanty $x chemie $x farmakologie $7 D054327
650    12
$a lubrikace $7 D008153
650    _2
$a mechanické jevy $7 D055595
650    _2
$a gama-globuliny $x chemie $7 D005719
655    _2
$a časopisecké články $7 D016428
655    _2
$a práce podpořená grantem $7 D013485
700    1_
$a Vrbka, Martin $u Faculty of Mechanical Engineering, Brno University of Technology, Czech Republic.
700    1_
$a Urban, Filip $u Faculty of Mechanical Engineering, Brno University of Technology, Czech Republic.
700    1_
$a Křupka, Ivan, $u Faculty of Mechanical Engineering, Brno University of Technology, Czech Republic. $d 1967- $7 mzk2002157050
700    1_
$a Hartl, Martin, $u Faculty of Mechanical Engineering, Brno University of Technology, Czech Republic. $d 1967- $7 mzk2002157052
773    0_
$w MED00166961 $t Journal of the mechanical behavior of biomedical materials $x 1878-0180 $g Roč. 55, č. - (2015), s. 295-307
856    41
$u https://pubmed.ncbi.nlm.nih.gov/26637935 $y Pubmed
910    __
$a ABA008 $b sig $c sign $y a $z 0
990    __
$a 20161005 $b ABA008
991    __
$a 20170117104349 $b ABA008
999    __
$a ok $b bmc $g 1166179 $s 952495
BAS    __
$a 3
BAS    __
$a PreBMC
BMC    __
$a 2015 $b 55 $c - $d 295-307 $e 20151119 $i 1878-0180 $m Journal of the mechanical behavior of biomedical materials $n J Mech Behav Biomed Mater $x MED00166961
LZP    __
$a Pubmed-20161005

Find record

Citation metrics

Loading data ...

Archiving options

Loading data ...