Degradation of the cyanotoxin microcystin-LR using iron-based photocatalysts under visible light illumination
Jazyk angličtina Země Německo Médium print-electronic
Typ dokumentu časopisecké články
PubMed
28677041
DOI
10.1007/s11356-017-9566-4
PII: 10.1007/s11356-017-9566-4
Knihovny.cz E-zdroje
- Klíčová slova
- Iron oxide, Microcystin, Mössbauer spectroscopy, Photocatalysis, Water treatment,
- MeSH
- adsorpce MeSH
- karcinogeny chemie MeSH
- katalýza MeSH
- koncentrace vodíkových iontů MeSH
- magnetické nanočástice chemie MeSH
- mikrocystiny chemie metabolismus MeSH
- mořské toxiny MeSH
- povrchové vlastnosti MeSH
- světlo * MeSH
- velikost částic MeSH
- železité sloučeniny chemie MeSH
- Publikační typ
- časopisecké články MeSH
- Názvy látek
- cyanoginosin LR MeSH Prohlížeč
- ferric oxide MeSH Prohlížeč
- karcinogeny MeSH
- magnetické nanočástice MeSH
- mikrocystiny MeSH
- mořské toxiny MeSH
- železité sloučeniny MeSH
In this study, a simple and low-cost method to synthesize iron(III) oxide nanopowders in large quantity was successfully developed for the photocatalytic degradation of microcystin-LR (MC-LR). Two visible light-active iron(III) oxide samples (MG-9 calcined at 200 °C for 5 h and MG-11 calcined at 180 °C for 16 h) with a particle size of 5-20 nm were prepared via thermal decomposition of ferrous oxalate dihydrate in air without any other modifications such as doping. The synthesized samples were characterized by X-ray powder diffraction, 57Fe Mössbauer spectroscopy, transmission electron microscopy, Brunauer-Emmett-Teller (BET) specific surface area analysis, and UV-visible diffuse reflectance spectroscopy. The samples exhibited similar phase composition (a mixture of α-Fe2O3 and γ-Fe2O3), particle size distribution (5-20 nm), particle morphology, and degree of agglomeration, but different specific surface areas (234 m2 g-1 for MG-9 and 207 m2 g-1 for MG-11). The results confirmed higher photocatalytic activity of the catalyst with higher specific surface area. The highest photocatalytic activity of the sample to decompose MC-LR was observed at solution pH of 3.0 and catalyst loading of 0.5 g L-1 due to large amount of MC-LR adsorption, but a little iron dissolution of 0.0065 wt% was observed. However, no iron leaching was observed at pH 5.8 even though the overall MC-LR removal was slightly lower than at pH 3.0. Thus, the pH 5.8 could be an appropriate operating condition for the catalyst to avoid problems of iron contamination by the catalyst. Moreover, magnetic behavior of γ-Fe2O3 gives a possibility for an easy separation of the catalyst particles after their use.
Zobrazit více v PubMed
Phys Chem Chem Phys. 2014 Aug 21;16(31):16515-23 PubMed
J Am Chem Soc. 2010 Jun 2;132(21):7436-44 PubMed
Water Res. 2011 Jun;45(12 ):3787-96 PubMed
J Colloid Interface Sci. 2010 Aug 1;348(1):167-76 PubMed
J Colloid Interface Sci. 2004 Jul 15;275(2):523-9 PubMed
Environ Sci Pollut Res Int. 2014 Oct;21(20):11781-93 PubMed
J Am Chem Soc. 2007 Sep 5;129(35):10929-36 PubMed
Int J Hematol. 2008 Jul;88(1):7-15 PubMed
J Hazard Mater. 2012 Apr 15;211-212:196-202 PubMed
Toxicol Lett. 1995 Dec;82-83:969-74 PubMed