A critical lack of personal protective equipment has occurred during the COVID-19 pandemic. Polylactic acid (PLA), a polyester made from renewable natural resources, can be exploited for 3D printing of protective face masks using the Fused Deposition Modelling technique. Since the possible high porosity of this material raised questions regarding its suitability for protection against viruses, we have investigated its microstructure using scanning electron microscopy and aerosol generator and photometer certified as the test system according to the standards EN 143 and EN 149. Moreover, the efficiency of decontaminating PLA surfaces by conventional chemical disinfectants including 96% ethanol, 70% isopropanol, and a commercial disinfectant containing 0.85% sodium hypochlorite has been determined. We confirmed that the structure of PLA protective masks is compact and can be considered a sufficient barrier protection against particles of a size corresponding to microorganisms including viruses. Complete decontamination of PLA surfaces from externally applied Staphylococcus epidermidis, Escherichia coli, Candida albicans and SARS-CoV-2 was achieved using all disinfectants tested, and human adenovirus was completely inactivated by sodium hypochlorite-containing disinfectant. Natural contamination of PLA masks worn by test persons was decontaminated easily and efficiently by ethanol. No disinfectant caused major changes to the PLA surface properties, and the pore size did not change despite severe mechanical damage of the surface. Therefore, PLA may be regarded as a suitable material for 3D printing of protective masks during the current or future pandemic crises.

• Klíčová slova
• 3D printing, COVID-19, Disinfection, Ethanol, Human adenovirus, Polylactic acid, Protective masks, Reusable material, SARS-CoV-2, Virological testing,
• Publikační typ
• časopisecké články MeSH

The mandatory face mask wearing was implemented in the Czech Republic and Slovakia shortly after the COVID-19 outbreak in Central Europe. So far, the number of COVID-19-associated deaths per 100,000 individuals is far lower in these countries as compared with other neighbouring or close countries. The use of face masks in public may not protect the general public from contracting the virus, however, presumptively decreases the viral load and contributes to a favourable clinical outcome in COVID-19 disease. A certain time is required for antigen-specific T cells and B cells to fully develop. Obligatory face mask wearing in public favours the virus transmission through oral mucosa and/or conjunctival epithelium, which enables the adaptive immune responses to evolve. In the case of inhalation of high loads of SARS-CoV-2, the time for the development of fully protective adaptive immune responses seems to be insufficient. Then, a less specific and more damaging innate immune response prevails.

• Klíčová slova
• COVID-19, COVID-19 face masks, immunity, transmission route, viral load,
• MeSH
• Betacoronavirus MeSH
• COVID-19 MeSH
• koronavirové infekce epidemiologie   prevence a kontrola   přenos   MeSH
• lidé MeSH
• masky * MeSH
• ochranné oděvy MeSH
• osobní ochranné prostředky MeSH
• pandemie prevence a kontrola   MeSH
• SARS-CoV-2 MeSH
• virová nálož MeSH
• virová pneumonie epidemiologie   prevence a kontrola   přenos   MeSH
• Check Tag
• lidé MeSH
• Publikační typ
• časopisecké články MeSH
• Geografické názvy
• Česká republika epidemiologie   MeSH
• Slovenská republika epidemiologie   MeSH

Outages in the supply of basic medical supplies and protective equipment have led to efforts to replace them. The team of BUT employees and students has developed a protective half mask that can also be printed on a standard 3D printer without the use of special materials. The original half mask is intended as an improvised protection that can be easily printed on standard 3D printers with FDM technology. Problematic possibilities of sealing the entire surface of the print due to its porosity were solved with the help of a nitrile examination glove. Commonly available equipment is enough to produce this half mask.

• Klíčová slova
• 3D FDM method, 3D printed mask, COVID-19 mask, Protective half-mask, filtration material,
• Publikační typ
• časopisecké články MeSH

COVID-19, classified as SARS-CoV-2, is causing an ongoing global pandemic. The pandemic has resulted in the loss of lives and has caused economic hardships. Most of the devices used to protect against the transmission of the novel COVID-19 disease are related to textile structures. Hence, the challenge for textile professionals is to design and develop suitable textile structures with multiple functionalities for capturing viruses, passivating them, and, at the same time, having no adverse effects on humans during the complete period of use. In addition to manufacturing efficient, biocompatible, and cost-effective protective face masks, it is also necessary to inform the public about the benefits and risks of protective face mask materials. The purpose of this article is to address the concerns of efficiency and efficacy of face masks by primarily reviewing the literature of research conducted at the Technical University of Liberec. The main focus is on the presentation of problems related to the specification of aims of face mask applications, mechanisms of capture, durability, and modes of sterilization. The recommendations, instead of conclusions, are addressed to the whole textile society because they should be leading players in the design, creation, and proper treatment of face masks due to their familiarity with the complex behavior of textile structures and targeted changes of structural hierarchy starting from polymeric chains (nano-level) and ending in planar textile structures (millimeter level) due to action by mechanical, physical and chemical fields. This becomes extremely critical to saving hundreds of thousands of lives from COVID-19.

• Klíčová slova
• COVID-19, anti-viral, facemask, nanoparticles, textiles,
• Publikační typ
• časopisecké články MeSH
• přehledy MeSH

The science around the use of masks by the public to impede COVID-19 transmission is advancing rapidly. In this narrative review, we develop an analytical framework to examine mask usage, synthesizing the relevant literature to inform multiple areas: population impact, transmission characteristics, source control, wearer protection, sociological considerations, and implementation considerations. A primary route of transmission of COVID-19 is via respiratory particles, and it is known to be transmissible from presymptomatic, paucisymptomatic, and asymptomatic individuals. Reducing disease spread requires two things: limiting contacts of infected individuals via physical distancing and other measures and reducing the transmission probability per contact. The preponderance of evidence indicates that mask wearing reduces transmissibility per contact by reducing transmission of infected respiratory particles in both laboratory and clinical contexts. Public mask wearing is most effective at reducing spread of the virus when compliance is high. Given the current shortages of medical masks, we recommend the adoption of public cloth mask wearing, as an effective form of source control, in conjunction with existing hygiene, distancing, and contact tracing strategies. Because many respiratory particles become smaller due to evaporation, we recommend increasing focus on a previously overlooked aspect of mask usage: mask wearing by infectious people ("source control") with benefits at the population level, rather than only mask wearing by susceptible people, such as health care workers, with focus on individual outcomes. We recommend that public officials and governments strongly encourage the use of widespread face masks in public, including the use of appropriate regulation.

• Klíčová slova
• COVID-19, SARS-CoV-2, masks, pandemic,
• MeSH
• COVID-19 * epidemiologie   prevence a kontrola   MeSH
• lidé MeSH
• masky * MeSH
• SARS-CoV-2 * MeSH
• trasování kontaktů * MeSH
• Check Tag
• lidé MeSH
• Publikační typ
• časopisecké články MeSH
• přehledy MeSH

OBJECTIVES: During the covid-19 pandemic, protective equipment such as respirators and masks were widely used to protect respiratory tract. This disposable protective equipment is usually made from plastic fibre-based nonwoven fabrics. If used masks and respirators are improperly discarded, they pollute the environment by becoming a source of micro and nanoplastics. The aim of the study was to find out how stable the materials of protective equipment are and how released nano and microplastics can affect aquatic and soil organisms. MATERIALS: The input materials used to produce respirators and masks were tested for their thermal stability and resistance to the release of plastic particles into the environment. To determine the thermal stability of the materials, a simultaneous thermal analysis - thermogravimetry (TGA) and differential scanning calorimetry (DSC) were performed. RESULTS: Materials of masks and respirators are stable at temperatures common to temperate climate zone. However, the possible effects of chemical reactions of the materials with the environment were not considered during the measurement. The materials were also subjected to ecotoxicity tests according to European standards. CONCLUSION: While the leachate obtained by shaking the materials in water did not show acute toxicity to the selected aquatic organisms, the material itself had a significant effect on selected soil organisms (springtails).

• Klíčová slova
• covid-19, ecotoxicity, environment, nonwoven fabrics, protective equipment,
• MeSH
• COVID-19 * prevence a kontrola   MeSH
• lidé MeSH
• pandemie MeSH
• plastické hmoty MeSH
• prostředky na ochranu dýchání * MeSH
• SARS-CoV-2 MeSH
• Check Tag
• lidé MeSH
• Publikační typ
• časopisecké články MeSH
• Názvy látek
• plastické hmoty MeSH

In this paper, the design and research of a sensor-based personal air-quality monitoring device are presented, which is retrofitted into different personal protective face masks. Due to its small size and low power consumption, the device can be integrated into and applied in practical urban usage. We present our research and the development of the sensor node based on a BME680-type environmental sensor cluster with a wireless IoT (Internet of Things)-capable central unit and overall low power consumption. The integration of the sensor node was investigated with traditional medical masks and a professional FFP2-type mask. The filtering efficiency after embedding was validated with a head model and a particle counter. We found that the professional mask withstood the embedding without losing the protective filtering aspect. We compared the inner and outer sensor data and investigated the temperature, pressure, humidity, and AQI (Air Quality Index) relations with possible sensor data-fusion options. The novelty is increased with the dual-sensor layout (inward and outward). It was found that efficient respiration monitoring is achievable with the device. With the analysis of the recorded data, characteristic signals were identified in an urban environment, enabling urban altimetry and urban zone detection. The results promote smart city concepts and help in endeavors related to SDGs (Sustainable Development Goals) 3 and 11.

• Klíčová slova
• IoT, air quality, embedded electronics, face mask, sensors, wearable,
• Publikační typ
• časopisecké články MeSH

The COVID-19 outbreak increased demand for personal protective respirator masks. Textile masks based on cloth materials appeared to be a sustainable, comfortable, and cost-effective alternative available in global communities. In this study, we used laser-based particle counting for mask material qualification to determine the concentration filtering efficiency in general, everyday community use. The efficiencies of eleven different commercially available textile materials were measured in single-, double-, and triple-layer configurations according to their grammage, mesh (XY), and inter-yarn gap. It was found that in the single-layer configurations, most materials were well below the acceptable standards, with a wide variation in filtering efficiency, which ranged from 5% to ~50%. However, when testing the fabrics in two or three layers, the efficiency increased significantly, exceeding or approaching the standard for medical masks. Three layers of natural silk was able to produce a level of filtration efficiency of 84.68%. Two-layered natural silk achieved 70.98%, cotton twill achieved 75.6%, and satin-weave viscose achieved 69.77%. Further options can also be considered in cases where lower filtration is acceptable It was statistically shown that applying a second layer was more significant in terms of overall filtering than increasing the layer count to three. However, layer stacking limited the breathability. The paper presents measurement-based qualitative and quantitative recommendations for future textile applications in face mask manufacturing.

• Klíčová slova
• COVID-19, filtering efficiency, laser-based particle counting, personal protective equipment, respirator, textile mask, textile material,
• Publikační typ
• časopisecké články MeSH

Running across the globe for nearly 2 years, the Covid-19 pandemic keeps demonstrating its strength. Despite a lot of understanding, uncertainty regarding the efficiency of interventions still persists. We developed an age-structured epidemic model parameterized with epidemiological and sociological data for the first Covid-19 wave in the Czech Republic and found that (1) starting the spring 2020 lockdown 4 days earlier might prevent half of the confirmed cases by the end of lockdown period, (2) personal protective measures such as face masks appear more effective than just a realized reduction in social contacts, (3) the strategy of sheltering just the elderly is not at all effective, and (4) leaving schools open is a risky strategy. Despite vaccination programs, evidence-based choice and timing of non-pharmaceutical interventions remains an effective weapon against the Covid-19 pandemic.

• Klíčová slova
• Age structure, Approximate Bayesian computation, Covid-19 pandemic, Non-pharmaceutical interventions, School closure,
• MeSH
• biologické modely MeSH
• COVID-19 * epidemiologie   prevence a kontrola   MeSH
• kontrola infekčních nemocí MeSH
• lidé MeSH
• masky * MeSH
• matematické pojmy MeSH
• pandemie prevence a kontrola   MeSH
• SARS-CoV-2 MeSH
• senioři MeSH
• školy MeSH
• Check Tag
• lidé MeSH
• senioři MeSH
• Publikační typ
• časopisecké články MeSH
• práce podpořená grantem MeSH
• Research Support, N.I.H., Extramural MeSH
• Geografické názvy
• Česká republika epidemiologie   MeSH

The recent pandemic has shown that protecting the general population from hazardous substances or pathogens can be a challenging and urgent task. The key element to adequate protection is appropriately sized, well-fitted and sufficiently distributed personal protective equipment (PPE). While these conditions are followed for adult PPE wearers, they are less considered when it comes to protecting subadults. In this study, the assessment of the fit and design improvements of a 3D-printed facial half mask for subadult wearers (4-18 years) is designed. The target population was represented by 1137 subadults, aged 4.06-18.94 years, for whom 3D face models were acquired. The half mask tested, which was originally provided in one subadult size, did not fit appropriately the target population. This finding prompted the creation of four size categories using the age-dependent distribution of the centroid size calculated from 7 facial landmarks. For each size category, a modified half-mask virtual design was created, including resizing and reshaping, and fit was evaluated visually and numerically using averaged and random 3D face representatives.Practitioner summary: The reason for this study was to describe procedures which led to design improvement of an existing half-mask and provide respiratory protection for subadults. To address this, fit was assessed using an innovative metric approach. Four sizes were then created based on centroid size, resulting in improved fit and design.Abbreviations: CH: cheilion landmark; CS: centroid size; EX: exocanthion landmark; GN: gnathion landmark; N: nasion landmark; PPE: personal protective equipment; PR: pronasale landmark; RPE: respiratory protective equipment.

3D human face dataset was used for modifying and validating protective equipment for subadultsTo ensure optimal protection for subadults, four size categories were proposed based on 3D face landmarks and centroid sizeModified half-mask design fit was validated virtually using a visual and numerical approach.

• Klíčová slova
• 3D face database, Personal protective equipment, centroid size, sizing system, subadults, virtual design, virtual fit assessment,
• MeSH
• 3D tisk MeSH
• COVID-19 prevence a kontrola   MeSH
• design vybavení * MeSH
• dítě MeSH
• lidé MeSH
• masky * MeSH
• mladiství MeSH
• obličej MeSH
• předškolní dítě MeSH
• prostředky na ochranu dýchání MeSH
• Check Tag
• dítě MeSH
• lidé MeSH
• mladiství MeSH
• mužské pohlaví MeSH
• předškolní dítě MeSH
• ženské pohlaví MeSH
• Publikační typ
• časopisecké články MeSH