-
Something wrong with this record ?
The effect of microstructure on fatigue performance of Ti-6Al-4V alloy after EDM surface treatment for application in orthopaedics
J. Stráský, M. Janeček, P. Harcuba, M. Bukovina, L. Wagner,
Language English Country Netherlands
Document type Journal Article, Research Support, Non-U.S. Gov't
- MeSH
- Electricity MeSH
- Mechanical Phenomena MeSH
- Microscopy, Electron, Scanning MeSH
- Orthopedics methods MeSH
- Tensile Strength MeSH
- Surface Properties MeSH
- Materials Testing MeSH
- Titanium chemistry MeSH
- Hot Temperature MeSH
- Publication type
- Journal Article MeSH
- Research Support, Non-U.S. Gov't MeSH
Three different microstructures--equiaxed, bi-modal and coarse lamellar--are prepared from Ti-6Al-4V alloy. Electric discharge machining (EDM) with a high peak current (29 A) is performed in order to impose surface roughness and modify the chemical composition of the surface. Detailed scanning electron microscopy (SEM) investigation revealed a martensitic surface layer and subsurface heat affected zone (HAZ). EDX measurements showed carbon enriched remnants of the EDM process on the material surface. Rotating bending fatigue tests are undertaken for EDM processed samples for all three microstructures and also for electropolished-benchmark-samples. The fatigue performance is found to be rather poor and not particularly dependent on microstructure. The bi-modal microstructure shows a slightly superior high cycle fatigue performance. This performance can be further improved by a suitable heat treatment to an endurance limit of 200 MPa.
References provided by Crossref.org
- 000
- 00000naa a2200000 a 4500
- 001
- bmc12022401
- 003
- CZ-PrNML
- 005
- 20170410101326.0
- 007
- ta
- 008
- 120806s2011 ne f 000 0#eng||
- 009
- AR
- 024 7_
- $a 10.1016/j.jmbbm.2011.06.012 $2 doi
- 035 __
- $a (PubMed)22098894
- 040 __
- $a ABA008 $b cze $d ABA008 $e AACR2
- 041 0_
- $a eng
- 044 __
- $a ne
- 100 1_
- $a Stráský, Josef $u Charles University, Department of Physics of Materials, Prague, Czech Republic.
- 245 14
- $a The effect of microstructure on fatigue performance of Ti-6Al-4V alloy after EDM surface treatment for application in orthopaedics / $c J. Stráský, M. Janeček, P. Harcuba, M. Bukovina, L. Wagner,
- 520 9_
- $a Three different microstructures--equiaxed, bi-modal and coarse lamellar--are prepared from Ti-6Al-4V alloy. Electric discharge machining (EDM) with a high peak current (29 A) is performed in order to impose surface roughness and modify the chemical composition of the surface. Detailed scanning electron microscopy (SEM) investigation revealed a martensitic surface layer and subsurface heat affected zone (HAZ). EDX measurements showed carbon enriched remnants of the EDM process on the material surface. Rotating bending fatigue tests are undertaken for EDM processed samples for all three microstructures and also for electropolished-benchmark-samples. The fatigue performance is found to be rather poor and not particularly dependent on microstructure. The bi-modal microstructure shows a slightly superior high cycle fatigue performance. This performance can be further improved by a suitable heat treatment to an endurance limit of 200 MPa.
- 650 _2
- $a elektřina $7 D004560
- 650 _2
- $a vysoká teplota $7 D006358
- 650 _2
- $a testování materiálů $7 D008422
- 650 _2
- $a mechanické jevy $7 D055595
- 650 _2
- $a mikroskopie elektronová rastrovací $7 D008855
- 650 _2
- $a ortopedie $x metody $7 D009985
- 650 _2
- $a povrchové vlastnosti $7 D013499
- 650 _2
- $a pevnost v tahu $7 D013718
- 650 _2
- $a titan $x chemie $7 D014025
- 655 _2
- $a časopisecké články $7 D016428
- 655 _2
- $a práce podpořená grantem $7 D013485
- 700 1_
- $a Janeček, Miloš
- 700 1_
- $a Harcuba, Petr
- 700 1_
- $a Bukovina, Michal
- 700 1_
- $a Wagner, Lothar
- 773 0_
- $w MED00166961 $t Journal of the mechanical behavior of biomedical materials $x 1878-0180 $g Roč. 4, č. 8 (2011), s. 1955-1962
- 856 41
- $u https://pubmed.ncbi.nlm.nih.gov/22098894 $y Pubmed
- 910 __
- $a ABA008 $b sig $c sign $y m $z 0
- 990 __
- $a 20120806 $b ABA008
- 991 __
- $a 20170410101624 $b ABA008
- 999 __
- $a ok $b bmc $g 944314 $s 779698
- BAS __
- $a 3
- BAS __
- $a PreBMC
- BMC __
- $a 2011 $b 4 $c 8 $d 1955-1962 $e 20110630 $i 1878-0180 $m Journal of the mechanical behavior of biomedical materials $n J Mech Behav Biomed Mater $x MED00166961
- LZP __
- $a Pubmed-20120806/12/01
