• Something wrong with this record ?

Newly developed Ti-Nb-Zr-Ta-Si-Fe biomedical beta titanium alloys with increased strength and enhanced biocompatibility

I. Kopova, J. Stráský, P. Harcuba, M. Landa, M. Janeček, L. Bačákova,

. 2016 ; 60 (-) : 230-8. [pub] 20151117

Language English Country Netherlands

Document type Journal Article, Research Support, Non-U.S. Gov't

Persistent link   https://www.medvik.cz/link/bmc16027785

Beta titanium alloys are promising materials for load-bearing orthopaedic implants due to their excellent corrosion resistance and biocompatibility, low elastic modulus and moderate strength. Metastable beta-Ti alloys can be hardened via precipitation of the alpha phase; however, this has an adverse effect on the elastic modulus. Small amounts of Fe (0-2 wt.%) and Si (0-1 wt.%) were added to Ti-35Nb-7Zr-6Ta (TNZT) biocompatible alloy to increase its strength in beta solution treated condition. Fe and Si additions were shown to cause a significant increase in tensile strength and also in the elastic modulus (from 65 GPa to 85 GPa). However, the elastic modulus of TNZT alloy with Fe and Si additions is still much lower than that of widely used Ti-6Al-4V alloy (115 GPa), and thus closer to that of the bone (10-30 GPa). Si decreases the elongation to failure, whereas Fe increases the uniform elongation thanks to increased work hardening. Primary human osteoblasts cultivated for 21 days on TNZT with 0.5Si+2Fe (wt.%) reached a significantly higher cell population density and significantly higher collagen I production than cells cultured on the standard Ti-6Al-4V alloy. In conclusion, the Ti-35Nb-7Zr-6Ta-2Fe-0.5Si alloy proves to be the best combination of elastic modulus, strength and also biological properties, which makes it a viable candidate for use in load-bearing implants.

References provided by Crossref.org

000      
00000naa a2200000 a 4500
001      
bmc16027785
003      
CZ-PrNML
005      
20161025120937.0
007      
ta
008      
161005s2016 ne f 000 0|eng||
009      
AR
024    7_
$a 10.1016/j.msec.2015.11.043 $2 doi
024    7_
$a 10.1016/j.msec.2015.11.043 $2 doi
035    __
$a (PubMed)26706526
040    __
$a ABA008 $b cze $d ABA008 $e AACR2
041    0_
$a eng
044    __
$a ne
100    1_
$a Kopova, Ivana $u Department of Biomaterials and Tissue Engineering, Institute of Physiology of the Czech Academy of Sciences, Videnska 1083, 14220 Prague 4, , Czech Republic. Electronic address: ivana.kopova@biomed.cas.cz.
245    10
$a Newly developed Ti-Nb-Zr-Ta-Si-Fe biomedical beta titanium alloys with increased strength and enhanced biocompatibility / $c I. Kopova, J. Stráský, P. Harcuba, M. Landa, M. Janeček, L. Bačákova,
520    9_
$a Beta titanium alloys are promising materials for load-bearing orthopaedic implants due to their excellent corrosion resistance and biocompatibility, low elastic modulus and moderate strength. Metastable beta-Ti alloys can be hardened via precipitation of the alpha phase; however, this has an adverse effect on the elastic modulus. Small amounts of Fe (0-2 wt.%) and Si (0-1 wt.%) were added to Ti-35Nb-7Zr-6Ta (TNZT) biocompatible alloy to increase its strength in beta solution treated condition. Fe and Si additions were shown to cause a significant increase in tensile strength and also in the elastic modulus (from 65 GPa to 85 GPa). However, the elastic modulus of TNZT alloy with Fe and Si additions is still much lower than that of widely used Ti-6Al-4V alloy (115 GPa), and thus closer to that of the bone (10-30 GPa). Si decreases the elongation to failure, whereas Fe increases the uniform elongation thanks to increased work hardening. Primary human osteoblasts cultivated for 21 days on TNZT with 0.5Si+2Fe (wt.%) reached a significantly higher cell population density and significantly higher collagen I production than cells cultured on the standard Ti-6Al-4V alloy. In conclusion, the Ti-35Nb-7Zr-6Ta-2Fe-0.5Si alloy proves to be the best combination of elastic modulus, strength and also biological properties, which makes it a viable candidate for use in load-bearing implants.
650    _2
$a biokompatibilní materiály $x chemie $x farmakologie $7 D001672
650    _2
$a železo $x chemie $7 D007501
650    _2
$a niob $x chemie $7 D009556
650    _2
$a osteogeneze $x účinky léků $7 D010012
650    _2
$a oxid křemičitý $x chemie $7 D012822
650    _2
$a titan $x chemie $7 D014025
655    _2
$a časopisecké články $7 D016428
655    _2
$a práce podpořená grantem $7 D013485
700    1_
$a Stráský, Josef $u Department of Physics of Materials, Faculty of Mathematics and Physics, Charles University in Prague, Ke Karlovu 5, 121 16 Prague 2, Czech Republic.
700    1_
$a Harcuba, Petr $u Department of Physics of Materials, Faculty of Mathematics and Physics, Charles University in Prague, Ke Karlovu 5, 121 16 Prague 2, Czech Republic.
700    1_
$a Landa, Michal $u Institute of Thermomechanics, Academy of Sciences of the Czech Republic, Dolejskova 5, 182 00 Prague 8, Czech Republic.
700    1_
$a Janeček, Miloš $u Department of Physics of Materials, Faculty of Mathematics and Physics, Charles University in Prague, Ke Karlovu 5, 121 16 Prague 2, Czech Republic.
700    1_
$a Bačákova, Lucie $u Department of Biomaterials and Tissue Engineering, Institute of Physiology of the Czech Academy of Sciences, Videnska 1083, 14220 Prague 4, , Czech Republic.
773    0_
$w MED00184559 $t Materials science & engineering. C, Materials for biological applications $x 1873-0191 $g Roč. 60, č. - (2016), s. 230-8
856    41
$u https://pubmed.ncbi.nlm.nih.gov/26706526 $y Pubmed
910    __
$a ABA008 $b sig $c sign $y a $z 0
990    __
$a 20161005 $b ABA008
991    __
$a 20161025121351 $b ABA008
999    __
$a ok $b bmc $g 1166099 $s 952415
BAS    __
$a 3
BAS    __
$a PreBMC
BMC    __
$a 2016 $b 60 $c - $d 230-8 $e 20151117 $i 1873-0191 $m Materials science & engineering. C, Materials for biological applications $n Mater Sci Eng C Mater Biol Appl $x MED00184559
LZP    __
$a Pubmed-20161005

Find record

Citation metrics

Archiving options