Metal powders for additive manufacturing are expensive, and producing new ones from mined metals has a negative ecological impact. In this work, recycled and reused metal powders from MS1 steel for direct metal laser sintering (DMLS) 3D printing were evaluated in the laboratory. The powders were recycled by melting followed by gas atomizing. Virgin, recycled, and reused metal powders were evaluated using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), metallography analysis, microhardness measurements, particle size distribution (PSD), shape factor by digital image processing (DIP), and flowability testing. The results showed that the particle distribution was modified after recycling. Kurtosis analysis revealed a reduction from -0.64 for virgin powders to -1.29 for recycled powders. The results demonstrated a positive skewness, indicating that the recycled powder contained a greater proportion of smaller particles. The shape factor was also modified and changed from 1.57 for virgin powders to 1.28 for recycled powders. The microstructure also changed, and austenite was found in the recycled powders. The microhardness of recycled powder decreased by 39% compared to the virgin powder. Recycled powders did not flow, using two different funnels to evaluate their flowability. The flowability of used powder was reduced from 4.3 s to 2.9 s.

Faculty of Mechanical Engineering University of West Bohemia Univerzitni 8 30614 Pilsen Czech Republic

Tribology and Surfaces Group Universidad Nacional de Colombia Sede Medellín Medellin 050034 Colombia

Zobrazit více v PubMed

Cooke S., Ahmadi K., Willerth S., Herring R. Metal additive manufacturing: Technology, metallurgy and modelling. J. Manuf. Process. 2020;57:978–1003. doi: 10.1016/j.jmapro.2020.07.025. DOI

Gu D., Shi X., Poprawe R., Bourell D.L., Setchi R., Zhu J. Material-structure-performance integrated laser-metal additive manufacturing. Science. 2021;372:eabg1487. doi: 10.1126/science.abg1487. PubMed DOI

Peng T., Kellens K., Tang R., Chen C., Chen G. Sustainability of additive manufacturing: An overview on its energy demand and environmental impact. Addit. Manuf. 2018;21:694–704. doi: 10.1016/j.addma.2018.04.022. DOI

Citarella R., Giannella V. Additive Manufacturing in Industry. Appl. Sci. 2021;11:840. doi: 10.3390/app11020840. DOI

Admin . Sustainable Practices and Waste Recycling in Metal Additive Manufacturing. Inside Metal Additive Manufacturing; Andover, UK: 2024. [(accessed on 11 November 2024)]. Available online: https://insidemetaladditivemanufacturing.com/2024/06/10/sustainable-practices-and-waste-recycling-in-metal-additive-manufacturing/

Alamos F.J., Schiltz J., Kozlovsky K., Attardo R., Tomonto C., Pelletiers T., Schmid S.R. Effect of powder reuse on mechanical properties of Ti-6Al-4V produced through selective laser melting. Int. J. Refract. Met. Hard Mater. 2020;91:105273. doi: 10.1016/j.ijrmhm.2020.105273. DOI

Alamos F.J., Schiltz J., Attardo R., Gatrell B.A., Tomonto C., Budzinski J., McGuffin-Cawley J., Pelletiers T., Schmid S.R. Effect of powder reuse on orthopedic metals produced through selective laser sintering. Manuf. Lett. 2021;31:40–44. doi: 10.1016/j.mfglet.2021.06.002. DOI

Ahmed F., Ali U., Sarker D., Marzbanrad E., Choi K., Mahmoodkhani Y., Toyserkani E. Study of powder recycling and its effect on printed parts during laser powder-bed fusion of 17-4 PH stainless steel. J. Mech. Work. Technol. 2019;278:116522. doi: 10.1016/j.jmatprotec.2019.116522. DOI

Sun H., Chu X., Liu Z., Gisele A., Zou Y. Selective Laser Melting of Maraging Steels Using Recycled Powders: A Comprehensive Microstructural and Mechanical Investigation. Met. Mater. Trans. A. 2021;52:1714–1722. doi: 10.1007/s11661-021-06180-1. DOI

Svozilova S., Torres J.A., Zetková I., Santa J.F. Evaluation of recycled and reused metal powders for DMLS 3D printing; Proceedings of the Congreso Internacional de Materiales (XII CIM 2024); Medellin, Colombia. 25–27 September 2024.

Opatová K., Zetková I., Kučerová L. Relationship between the Size and Inner Structure of Particles of Virgin and Re-Used MS1 Maraging Steel Powder for Additive Manufacturing. Materials. 2020;13:956. doi: 10.3390/ma13040956. PubMed DOI PMC

EOS GmbH MDS EOS MaragingSteel MS1. [(accessed on 17 October 2024)]. Available online: https://www.eos.info/metal-solutions/metal-materials/data-sheets/mds-eos-maragingsteel-ms1.

Sajbura A., Sokolowski P. Ultrasonic Atomization as a Novel Route for the Metal Powder Development; Proceedings of the International Thermal Spray Conference; Québec City, QC, Canada. 22–25 May 2023; pp. 735–741.

Standard Test Methods for Flow Rate of Metal Powders Using the Hall Flowmeter Funnel. ASTM; West Conshohocken, PA, USA: 2020.