The lifetime and properties of cutting tools and forming moulds can be prolonged and enhanced by the deposition of hard, thin coatings. After a certain period of usage, the coating will deteriorate. Any remaining coating must be removed prior to successful recoating. Laser stripping is a fast and environmentally friendly coating removal method. In this paper, we present laser removal of two types of coatings deposited on a 1.2379 tool steel substrate, namely, an AlTiN coating with high hardness and a DLC C coating with a small coefficient of friction (COF). A powerful nanosecond laser was employed to remove the coating from the substrate with high efficiency, along with suitable residual surface roughness. Measurements were taken of surface roughness, removed depth, and working time on a stripped area of 1 cm2. The samples were evaluated under a microscope, with a 3D profilometer, and by EDS chemical analysis. Successful removal of the coating was confirmed by optical analysis, but detailed chemical characterisation showed that about 30% of the coating element may remain on the surface. Moreover, a working time of less than 7.5 s per cm2 was obtained in this study. In addition, it was shown that the application of a second low energy, high frequency laser beam pass leads to remelting of the peaks of the material and reduced surface roughness.

Department of Machining Process Planning and Metrology Faculty of Mechanical Engineering Czech Technical University 166 07 Prague Czech Republic

Department of Production Machines and Equipment Faculty of Mechanical Engineering Czech Technical University 128 00 Prague Czech Republic

Hofmeister s r o 301 00 Plzeň Czech Republic

Zobrazit více v PubMed

Dasch J.M., Ang C.C., Wong C.A., Cheng Y.T., Weiner A.M., Lev L.C., Konca E. A comparison of five categories of carbon-based tool coatings for dry drilling of aluminum. Surf. Coat. Technol. 2006;2006:2970–2977. doi: 10.1016/j.surfcoat.2005.04.025. DOI

Bouzakis K.D., Michailidis N., Skordaris G., Bouzakis E., Biermann D., M’Saoubi R. Cutting with coated tools: Coating technologies, characterization methods and performance optimization. CIRP J. Manuf. Sci. Technol. 2012;21 doi: 10.1016/j.cirp.2012.05.006. DOI

Conradie P.J.T., Oosthuizen G.A., Dimitrov D. On the effect of regrinding cutting tools for high performance milling of titanium alloys. Int. J. Adv. Manuf. Technol. 2017;90:2283–2292. doi: 10.1007/s00170-016-9550-z. DOI

Leyendecker T., Lemmer O., Esser S., Ebberink J. The development of the PVD coating TiAlN as a commercial coating for cutting tools. Surf. Coat. Technol. 1991;48:175–178. doi: 10.1016/0257-8972(91)90142-J. DOI

Saha B., Toh W.Q., Liu E., Tor S.B., Hardt D.E., Lee J. A review on the importance of surface coating of micro/nano-mold in mirco/nano-molding processes. J. Micromech. Microeng. 2015;26:13002. doi: 10.1088/0960-1317/26/1/013002. DOI

Bewilogua K., Hofmann D. History of diamond-like carbon films—From first experiments to worldwide applications. Surf. Coat. Technol. 2014;242:214–225. doi: 10.1016/j.surfcoat.2014.01.031. DOI

Dearnaley G., Arps J.H. Biomedical applications of diamond-like carbon (DLC) coatings: A review. Surf. Coat. Technol. 2005;200:2518–2524. doi: 10.1016/j.surfcoat.2005.07.077. DOI

Charmeau J.Y., Chailly M., Gilbert V., Béreaux Y. Influence of mold surface coatings in injection molding. Application to the ejection stage. Int. J. Mater. Form. 2008;1:699–702. doi: 10.1007/s12289-008-0311-x. DOI

Toboła D., Czechowski K., Wrońska I., Łętocha A., Miller T. The effects of the coating stripping process on regenerated tool cutting edges. J. Achiev. Mater. Manuf. Eng. 2013;61:294–301.

Conde A., Cristóbal A.B., Fuentes G., Tate T., De Damborenea J. Surface analysis of electrochemically stripped CrN coatings. Surf. Coat. Technol. 2006;201:3588–3595. doi: 10.1016/j.surfcoat.2006.08.110. DOI

Bonacchi D., Rizzi G., Bardi U., Scrivani A. Chemical stripping of ceramic films of titanium aluminum nitride from hard metal substrates. Surf. Coat. Technol. 2003;165:35–39. doi: 10.1016/S0257-8972(02)00720-X. DOI

Bobzin K. High-performance coatings for cutting tools. CIRP J. Manuf. Sci. Technol. 2017;18:1–9. doi: 10.1016/j.cirpj.2016.11.004. DOI

Şen Y., Ürgen M., Kazmanlı K., Çakır A.F. Stripping of CrN from CrN-coated high-speed steels. Surf. Coat. Technol. 1999;113:31–35. doi: 10.1016/S0257-8972(98)00814-7. DOI

Shugurov A.R., Kazachenok M.S. Mechanical properties and tribological behavior of magnetron sputtered TiAlN/TiAl multilayer coatings. Surf. Coat. Technol. 2018;353:254–262. doi: 10.1016/j.surfcoat.2018.09.001. DOI

Schubert E., Schutte K., Emmel A., Bergmann H.W. Excimer laser assisted TiN and WC removal from tools as a novel decoating technology. Proc. SPIE. 1995;2502:654–663. doi: 10.1117/12.204987. DOI

Sundar M., Whitehead D., Mativenga P.T., Li L., Cooke K.E. Excimer laser decoating of chromium titanium aluminium nitride to facilitate re-use of cutting tools. Opt. Laser Technol. 2009;41:938–944. doi: 10.1016/j.optlastec.2009.04.003. DOI

Marimuthu S., Kamara A.M., Whitehead D., Mativenga P., Li L. Laser removal of TiN coatings from WC micro-tools and in-process monitoring. Opt. Laser Technol. 2010;42:1233–1239. doi: 10.1016/j.optlastec.2010.03.016. DOI

Marimuthu S., Kamara A.M., Whitehead D., Mativenga P., Li L., Yang S., Cooke K. Laser stripping of TiAlN coating to facilitate reuse of cutting tools. J. Eng. Manuf. 2011;225:1851–1862. doi: 10.1177/0954405411414313. DOI

Hu C., He G., Chen J., Fang Z., Yang Z., Zhang Z. Research on Cleaning Mechanism of Anti-Erosion Coating Based on Thermal and Force Effects of Laser Shock. Coatings. 2020;10:683. doi: 10.3390/coatings10070683. DOI

See T.L., Chantzis D., Royer R., Metsios I., Antar M., Marimuthu S. Ultraviolet-Diode Pump Solid State Laser Removal of Titanium Aluminium Nitride Coating from Tungsten Carbide Substrate. Lasers Manuf. Mater. Process. 2017;4:93–107. doi: 10.1007/s40516-017-0039-x. DOI

Ragusich A., Taillon G., Meunier M., Martinu L., Klemberg-Sapieha J.E. Selective pulsed laser stripping of TiAlN erosion-resistant coatings: Effect of wavelength and pulse duration. Surf. Coat. Technol. 2013;232:758–766. doi: 10.1016/j.surfcoat.2013.06.092. DOI

Zivelonghi A., Giorleo L., Gelfi M., Ceretti E., La Vecchia G.M. Laser decoating of DLC films for tribological applications. Int. J. Adv. Manuf. Technol. 2017;93:1717–1724. doi: 10.1007/s00170-017-0482-z. DOI

Assurin S.R., Mativenga P., Rajab F., Cooke K., Field S. Laser de-coating of hard DLC coatings from tungsten carbide cutting tool. Proc. Inst. Mech. Eng. Part B J. Eng. Manuf. 2021;235:13–22. doi: 10.1177/0954405420962389. DOI

Rizzo A., Goel S., Grilli M.L., Iglesias R., Jaworska L., Lapkovskis V., Novak P., Postolnyi B.O., Valerini D. The Critical Raw Materials in Cutting Tools for Machining Applications: A Review. Materials. 2020;13:1377. doi: 10.3390/ma13061377. PubMed DOI PMC

Erdemir A., Donnet C. Tribology of diamond-like carbon films: Recent progress and future prospects. J. Phys. D Appl. Phys. 2006;39:311–327. doi: 10.1088/0022-3727/39/18/R01. DOI

Donnet C., Erdemir A. New horizon in the tribology of diamond like carbon films. Surf. Eng. 2013;24:399–401. doi: 10.1179/174329408X365666. DOI

Manninen N.K., Ribeiro F., Escudeiro A., Polcar T., Carvalho S., Cavaleiro A. Influence of Ag content on mechanical and tribological behavior of DLC coatings. Surf. Coat. Technol. 2013;232:440–446. doi: 10.1016/j.surfcoat.2013.05.048. DOI

Leitz K.H., Redlingshöfer B., Reg Y., Otto A., Schmidt M. Metal Ablation with Short and Ultrashort Laser Pulses. Phys. Procedia. 2011;12:230–238. doi: 10.1016/j.phpro.2011.03.128. DOI

Temmler A., Willenborg E., Wissenbach K., Cooke K., Field S. Laser polishing. Proc. SPIE Int. Soc. Opt. Eng. 2012;8243:13. doi: 10.1117/12.906001. DOI

Klemm A.J., Sanjeevan P. Application of laser speckle analysis for the assessment of cementitious surfaces subjected to laser cleaning. Appl. Surf. Sci. 2008;254:2642–2649. doi: 10.1016/j.apsusc.2007.10.007. DOI

Razab M.K.A.A., Jaafar M.S., Abdullah N.H., Suhaimi F.M., Mohamed M., Adam N., Yusuf N.A.A.N. A review of incorporating Nd:YAG laser cleaning principal in automotive industry. J. Radiat. Res. Appl. Sci. 2018;11:393–402. doi: 10.1016/j.jrras.2018.08.002. DOI

Kononenko T.V., Garnov S.V., Pimenov S.M., Konov V.I., Romano V., Borsos B., Weber H.P. Laser ablation and micropatterning of thin TiN coatings. Appl. Phys. A Mater. Sci. Process. 2000;71:627–631. doi: 10.1007/s003390000572. DOI