Metal three-dimensional (3D) printing technology brings several benefits to the field of high-pressure die casting of aluminum, which enhances its development. The associated conformal cooling application is already commonly used where there is a need to improve the quality of castings, increase tool life, or reduce the production cycle. However, will this technology withstand the production of a large part (∼270 × 270 × 200 mm), which will be used directly in the serial production of engine blocks? This article describes a slider with a conformal cooling case study, which was redesigned and manufactured using the laser powder bed fusion (L-PBF) method. After the slider was put into serial production of 1.0 TSI three-cylinder engine blocks, this tool was thoroughly monitored based on the temperature field by comparing the results of a simulation in SW ProCAST with reality, and furthermore examining the influence of the tool on the quality of castings. There was also an evaluation of repairs performed on the tool in the ŠKODA AUTO tool shop and the foundry. These data were compared with a serial tool. Finally, the costs to produce the slider in conventional and 3D-printed variants are compared with an outline of other possible steps for optimizing these costs. The study results show that relatively large parts can be printed and used in serial production even today. It was also confirmed that conformal cooling influenced improving tool life, and the number of repairs in ŠKODA AUTO production also decreased.

1 P4 34 Additive Manufacturing Center Metal Audi AG Ingolstadt Germany

Department of Machining Process Planning and Metrology Faculty of Mechanical Engineering The Czech Technical University Prague Prague Czech Republic

PSW F Casting Tool Production ŠKODA AUTO a s Mladá Boleslav Czech Republic

Zobrazit více v PubMed

Hassen AA, Noakes M, Nandwana P, et al. . Scaling up metal additive manufacturing process to fabricate molds for composite manufacturing. Addit Manuf 2020;32:101093; doi: 10.1016/j.addma.2020.101093 DOI

The American Mold Builders Association. Annual Business Forecast Report 2018. The American Mold Builders Association: Indianapolis, IN; 2019.

Ngo TD, Kashani A, Imbalzano G, et al. . Additive manufacturing (3D printing): A review of materials, methods, applications and challenges. Compos B Eng 2018;143:172–196; doi: 10.1016/j.compositesb.2018.02.012 DOI

Asnafi N. Tool and die making, surface treatment, and repair by laser-based additive processes. BHM Berg Und Hüttenmännische Monatshefte 2021;166:225–236; doi: 10.1007/s00501-021-01113-2 DOI

Nycz A, Adediran AI, Noakes MW, et al. Large Scale Metal Additive Techniques Review. In: Proceedings of the 27th Annual International Solid Freeform Fabrication Symposium. 2016. —An Additive Manufacturing Conference: Austin, Texas, USA; 2016.

Griffiths L. GE Additive Is Building the World's Largest Laser-Powder 3D Printing System. Available from: https://www.tctmagazine.com/additive-manufacturing-3d-printing-news/ge-additive-creating-worlds-largest-laser-3d-printing [Last accessed: July 9, 2021].

Stolt R, André S, Elgh F. Introducing inserts for die casting manufactured by selective laser sintering. Proc Manuf 2018;17:309–316; doi: 10.1016/j.promfg.2018.10.051 DOI

Brøtan V, Berg OÅ, Sørby K. Additive manufacturing for enhanced performance of molds. Proc CIRP 2016;54:186–190; doi: 10.1016/j.procir.2016.05.074 DOI

Kovács SE, Varga L, Szentes Z. Analysis of a special, 3D metal-printed HPDC tool material. Int J Eng Manage Sci 2020;5:251–265; doi: 10.1007/s00170-013-5523-7 DOI

Armillotta A, Baraggi R, Fasoli S. SLM tooling for die casting with conformal cooling channels. Int J Adv Manuf Technol 2014;71:573–583; doi: 10.1007/s00170-013-5523-7 DOI

Piekło J, Garbacz-Klempka A. Use of maraging steel 1.2709 for implementing parts of pressure mold devices with conformal cooling system. Materials 2020;13:5533; doi: 10.3390/ma13235533 PubMed DOI PMC

Stolt R, Jarfors AEW. Manufacturing of High Pressure Die Casting Die Inserts Using SLM. In: SPS2020. IOS Press, Advances in Transdisciplinary Engineering. 2020;2020-12-10. doi: 10.3233/ATDE200206

Jarfors AEW, Sevastopol R, Seshendra K, et al. . On the use of conformal cooling in high-pressure die-casting and semisolid casting. Technologies 2021;9:39; doi: 10.1007/s00501-021-01113-2 DOI

Kanbur BB, Supig S, Duan F. Design and optimization of conformal cooling channels for injection molding: A review. Int J Adv Manuf Technol 2020;106:3253–3271; doi: 10.1007/s00170-019-04697-9 DOI

Feng S, Kamat AM, Pei Y. Design and fabrication of conformal cooling channels in molds: Review and progress updates. Int J Heat Mass Transf 2021;171:121082; doi: 10.1016/j.ijheatmasstransfer.2021.121082 DOI

Brooks H, Brigden K. Design of conformal cooling layers with self-supporting lattices for additively manufactured tooling. Addit Manuf 2016;11:16–22; doi: 10.1016/j.addma.2016.03.004 DOI

Berger GR, Zorn D, Friesenbichler W, et al. . Efficient cooling of hot spots in injection molding. A biomimetic cooling channel versus a heat-conductive mold material and a heat conductive plastics. Polym Eng Sci 2019;59:E180–E188; doi: 10.1002/pen.25024 DOI

Wang L, Wei QS, Xue PJ, et al. . Fabricate mould insert with conformal cooling channel using selective laser melting. Adv Mater Res 2012;502:67–71; doi: 10.4028/www.scientific.net/AMR.502.67

Minguella-Canela J, Morales Planas S, De los Santos-López MA. SLM manufacturing redesign of cooling inserts for high production steel moulds and benchmarking with other industrial additive manufacturing strategies. Materials 2020;13:4843; doi: 10.3390/ma13214843 PubMed DOI PMC

Mazur M, Leary M, McMillan M, et al. . SLM additive manufacture of H13 tool steel with conformal cooling and structural lattices. Rapid Prototyp J 2016;22:504–518; doi:10.1108/RPJ-06-2014-0075 DOI

Oter ZC, Coskun M, Akca Y, et al. . Benefits of laser beam based additive manufacturing in die production. Optik 2019;176:175–184; doi: 10.1016/j.ijleo.2018.09.079 DOI

Cortina M, Arrizubieta J, Calleja A, et al. . Case study to illustrate the potential of conformal cooling channels for hot stamping dies manufactured using hybrid process of laser metal deposition (LMD) and milling. Metals 2018;8:102; doi: 10.3390/met8020102 DOI

Sinico M, Ranjan R, Moshiri M, et al. A Mold Insert Case Study on Topology Optimized Design for Additive Manufacturing. In: Proceedings of the 30th Annual International Solid Freeform Fabrication Symposium: An Additive Manufacturing Conference: Austin, TX, 2019; pp. 1921–1931.

Petrič M, Lavtar L, Taljat B, et al. Optimization of Cooling-Heating System in HPDC Tools. In: Livarsko posvetovanje Conference: Slovenija, 2016.

Fiorentini F, Curcio P, Armentani E, et al. . Study of two alternative cooling systems of a mold insert used in die casting process of light alloy components. Proc Struct Integr 2019;24:569–582; doi: 10.1016/j.prostr.2020.02.050 DOI

Malca C, Santos C, Sena M, et al. . Development of SLM cellular structures for injection molds manufacturing. Sci Technol Mater 2018;30:13–22; doi: 10.1016/j.stmat.2018.03.001 DOI

Kang J, Shangguan H, Deng C, et al. . Additive manufacturing-driven mold design for castings. Addit Manuf 2018;22:472–478; doi: 10.1016/j.addma.2018.04.037 DOI

Voestalpine. The Importance of Design for AM. Available from: https://www.voestalpine.com/additive-manufacturing/app/uploads/sites/53/2020/10/case_study_HPDC-The-Importance-of-Design-for-AM.pdf [Last accessed: November 13, 2021].

Voestalpine. Additive Manufacturing— The Next Dimension in HPDC Tooling. Available from:https://www.voestalpine.com/additive-manufacturing/app/uploads/sites/53/2020/07/AM-HPDC.pdf [Last accessed: November 13, 2021].

Voestalpine. AM Distributor & Distributor Ring Solutions. Available from: https://www.voestalpine.com/additive-manufacturing/app/uploads/sites/53/2020/07/case_study_distributor.pdf [Last accessed: May 13, 2021].

DebRoy T, Wei HL, Zuback JS, et al. . Additive manufacturing of metallic components—Process, structure and properties. Prog Mater Sci 2018;92:112–224; doi: 10.1016/j.pmatsci.2017.10.001 DOI

Blakey-Milner B, Gradl P, Snedden G, et al. . Metal additive manufacturing in aerospace: A review. Mater Des 2021;209:110008; doi: 10.1016/j.matdes.2021.110008 DOI

Biedermann M, Beutler P, Meboldt M. Automated design of additive manufactured flow components with consideration of overhang constraint. Addit Manuf 2021;46:102119; doi: 10.1016/j.addma.2021.102119 DOI

Mutua J, Nakata S, Onda T, et al. . Optimization of selective laser melting parameters and influence of post heat treatment on microstructure and mechanical properties of maraging steel. Mater Des 2018;139:486–497; doi: 10.1016/j.matdes.2017.11.042 DOI

EOS. ToolSteel 1.2709 Material Data Sheet. Available from: https://www.eos.info/03_system-related-assets/material-related-contents/metal-materials-and-examples/metal-material-datasheet/werkzeugstahl_ms1_cx/material_datasheet_eos_toolsteel_1.2709_premium_en_2020_web.pdf [Last accessed: September 23, 2021].

Bai Y, Yang Y, Wang D, et al. . Influence mechanism of parameters process and mechanical properties evolution mechanism of maraging steel 300 by selective laser melting. Mater Sci Eng 2017;703:116–123; doi: 10.1016/j.msea.2017.06.033 DOI

Andronov V, Šimota J, Beránek L, et al. . Optimization of process parameters for additively produced tool steel 1.2709 with a layer thickness of 100μm. Materials 2021;14:2852; doi: 10.3390/ma14112852 PubMed DOI PMC

Rashid R, Masood SH, Ruan D, et al. . Effect of scan strategy on density and metallurgical properties of 17-4PH parts printed by selective laser melting (SLM). J Mater Process Technol 2017;249:502–511; doi: 10.1016/j.jmatprotec.2017.06.023 DOI