This article aims to review a redesign approach of a student racing car's clutch lever component, which was topologically optimized and manufactured by Additive Manufacturing (AM). Finite Element Method (FEM) analysis was conducted before and after a Topology Optimization (TO) process in order to achieve equivalent stiffness and the desired safety factor for the optimized part. The redesigned clutch lever was manufactured by using AM-Selective Laser Melting (SLM) and printed from powdered aluminum alloy AlSi10Mg. The final evaluation of the study deals with the experimental test and comparison of the redesigned clutch lever with the existing part which was used in the previous racing car. Using TO as a main redesign tool and AM brought significant changes to the optimized part, especially the following: reduced mass of the component (10%), increased stiffness, kept safety factor above the 3.0 value and ensured the more aesthetic design and a good surface quality. Moreover, using TO and AM gave the opportunity to consolidate multi-part assembly into a single component manufactured by one manufacturing process that reduced the production time. The experimental results justified the simulation results and proved that even though the applied load was almost 1.5× higher than the assumed one, the maximum von Mises stress on the component was still below the yield limit of 220 MPa.

Department of Fundamentals of Machinery Design Faculty of Mechanical Engineering Silesian University of Technology 44 100 Gliwice Poland

Department of Machining Assembly and Engineering Metrology Faculty of Mechanical Engineering VSB Technical University of Ostrava 70800 Ostrava Czech Republic

Institute of Transport Faculty of Mechanical Engineering VSB Technical University of Ostrava 17 Listo padu 15 2172 70800 Ostrava Czech Republic

See more in PubMed

Bendsoe M.P., Sigmund O. Topology Optimization: Theory, Methods and Applications. Springer; Berlin, Germany: 2003. pp. 1–68.

Sotola M., Marsalek P., Rybansky D., Fusek M., Gabriel D. Sensitivity Analysis of Key Formulations of Topology Optimization on an Example of Cantilever Bending Beam. Symmetry. 2021;13:712. doi: 10.3390/sym13040712. DOI

Zhu J.H., Zhang W.H., Xia L. Topology Optimization in Aircraft and Aerospace Structures Design. Arch. Comput. Methods Eng. 2016;23:595–622. doi: 10.1007/s11831-015-9151-2. DOI

Hanush S.S., Manjaiah M. Topology optimization of aerospace part to enhance the performance by Finite manufacturing process. Mater. Today Proc. 2022;62:7373–7378. doi: 10.1016/j.matpr.2022.02.074. DOI

Prathyusha A.L.R., Babu G.R. A review on additive manufacturing and topology optimization process for weight reduction studies in various industrial applications. Mater. Today Proc. 2022;62:109–117. doi: 10.1016/j.matpr.2022.02.604. DOI

Jankovics D., Barari A. Customization of Automotive Structural Components using Additive Manufacturing and Topology Optimization. IFAC-Pap. 2019;52:212–217. doi: 10.1016/j.ifacol.2019.10.066. DOI

Bao D.W., Yan X., Snooks R., Xie Y. Bioinspired Generative Architectural Design Form-Finding and Advanced Robotic Fabrication Based on Structural Performance 2020. In: Yuan P., Xie M., Leach N., Yao J., Wang X., editors. Architectural Intelligence, Selected Papers from the 1st International Conference on Computational Design and Robotic Fabrication. Springer; Singapore: 2019. pp. 147–170. DOI

Li Y., Lai Y., Lu G., Yan F., Wei P., Xie Y.M. Innovative design of long-span steel–concrete composite bridge using multi-material topology optimization. Eng. Struct. 2022;269:114838. doi: 10.1016/j.engstruct.2022.114838. DOI

Reis P., Volpini M., Maia J.P., Guimarães I.B., Evelise C., Monteiro M., Rubio J.C.C. Resting hand splint model from topology optimization to be produced by additive manufacturing. Rapid Prototyp. J. 2022;28:216–225. doi: 10.1108/RPJ-07-2020-0176. DOI

Muzalewska M. Methodology of Multicriterial Optimization of Geometric Features of an Orthopedic Implant. Appl. Sci. 2021;11:11070. doi: 10.3390/app112211070. DOI

Zhang W., Zhu J., Gao T. Topology Optimization in Engineering Structure Design. Elsevier; Amsterdam, The Netherlands: 2016. DOI

Xia L. Multiscale Structural Topology Optimization. Elsevier; London, UK: 2016. DOI

Wylezol M. Topological Optimization in Mechanical Constructions—An Example of Application; Proceedings of the 5th International Scientific and Business Conference—Future Engineering; Oltarzew, Poland. 29–30 May 2019; DOI

Skarka W., Pabian T., Wąsik M. Topology Optimization Approach in a Process of Designing of Composite Shell Structures; Proceedings of the 25th ISPE Inc. International Conference on Transdisciplinary Engineering; Modena, Italy. 3–6 July 2018; DOI

Korkmaz M.E., Gupta M.K., Robak G., Moj K., Krolczyk G.M., Kuntoğlu M. Development of lattice structure with selective laser melting process: A state of the art on properties, future trends and challenges. J. Manuf. Process. 2022;81:1040–1063. doi: 10.1016/j.jmapro.2022.07.051. DOI

Milewski J.O. From Fundamental Technology to Rocket Nozzles, Medical Implants, and Custom Jewelry. Springer International Publishing AG; Cham, Switzerland: 2017. Additive Manufacturing of Metals; pp. 7–33.

3D Printing Center PROTOLAB. [(accessed on 22 August 2022)]. Available online: https://protolab.cz/

Student Racing Competition Rules. [(accessed on 22 August 2022)]. Available online: https://formulastudent.de/fileadmin/user_upload/all/2022/rules/FS-Rules_2022_v0.9.pdf.

Mesicek J., Pagac M., Petru J., Novak P., Hajnys J., Kutiova K. Topological optimization of the formula student bell crank. MM Sci. J. 2019:2964–2968. doi: 10.17973/MMSJ.2019_10_201893. DOI

Markovits T., Szederkény B. Investigation of generative design for powder bed fusion technology in case of Formula Student race car components using Ti6Al4V alloy. J. Manuf. Process. 2022;80:220–231. doi: 10.1016/j.jmapro.2022.05.058. DOI

Jancar L., Pagac M., Mesicek J., Stefek P. Design Procedure of a Topologically Optimized Scooter Frame Part. Symmetry. 2020;12:755. doi: 10.3390/sym12050755. DOI

Mertens A., Delahaye J., Dedry O., Vertruyen B., Tchuindjang J.T., Habraken A.M. Microstructure and Properties of SLM AlSi10Mg: Understanding the Influence of the Local Thermal History. Procedia Manuf. 2020;47:1089–1095. doi: 10.1016/j.promfg.2020.04.121. DOI

Atomised Aluminium Alloy Powder. [(accessed on 25 August 2022)]. Available online: https://www.metal-am.com/articles/selecting-atomised-aluminium-alloy-powders-for-the-metal-3d-printing-process/

Park T.-H., Baek M.-S., Hyer H., Sohn Y., Lee K.-A. Effect of direct aging on the microstructure and tensile properties of AlSi10Mg alloy manufactured by selective laser melting process. Mater. Charact. 2021;176:111113. doi: 10.1016/j.matchar.2021.111113. DOI

Bai S., Perevoshchikova N., Sha Y., Wu X. The Effects of Selective Laser Melting Process Parameters on Relative Density of the AlSi10Mg Parts and Suitable Procedures of the Archimedes Method. Appl. Sci. 2019;9:583. doi: 10.3390/app9030583. DOI

Read N., Wang W., Essa K., Attallah M.M. Selective laser melting of AlSi10Mg alloy: Process optimisation and mechanical properties development. Mater. Des. 2015;65:417–424. doi: 10.1016/j.matdes.2014.09.044. DOI

Martin J., Yahata B., Hundley J., Mayer J.A., Schaedler T.A., Pollock T.M. 3D printing of high-strength aluminium alloys. Nature. 2017;549:365–369. doi: 10.1038/nature23894. PubMed DOI

Muhammad M., Nezhadfar P.D., Thompson S., Saharan A., Phan N., Shamsaei N. A comparative investigation on the microstructure and mechanical properties of additively manufactured aluminum alloys. Int. J. Fatigue. 2021;146:106165. doi: 10.1016/j.ijfatigue.2021.106165. DOI

Ma Q.-P., Mesicek J., Fojtik F., Hajnys J., Krpec P., Pagac M., Petru J. Residual Stress Build-Up in Aluminum Parts Fabricated with SLM Technology Using the Bridge Curvature Method. Materials. 2022;15:6057. doi: 10.3390/ma15176057. PubMed DOI PMC

Pan W., Ye Z., Zhang Y., Liu Y., Liang B., Zhai Z. Research on Microstructure and Properties of AlSi10Mg Fabricated by Selective Laser Melting. Materials. 2022;15:2528. doi: 10.3390/ma15072528. PubMed DOI PMC

Li W., Li S., Liu J., Zhang A., Zhou Y., Wei Q., Yan C., Shi Y. Effect of heat treatment on AlSi10Mg alloy fabricated by selective laser melting: Microstructure evolution, mechanical properties and fracture mechanism. Mater. Sci. Eng. A. 2016;663:116–125. doi: 10.1016/j.msea.2016.03.088. DOI

Mesicek J., Cegan T., Ma Q.-P., Halama R., Skotnicova K., Hajnys J., Jurica J., Krpec P., Pagac M. Effect of artificial aging on the strength, hardness, and residual stress of SLM AlSi10Mg parts prepared from the recycled powder. Mater. Sci. Eng. 2022;855:143900. doi: 10.1016/j.msea.2022.143900. DOI

RENISHAW: Materials Catalog (MDS) Wotton-Under-Edg, Great Britain: Renishaw. 2022. [(accessed on 25 August 2022)]. Available online: https://www.renishaw.cz/cs/katalogove-listy-aditivni-vyroba--17862.

User Guide, Altair OptiStruct. [(accessed on 14 September 2022)]. Available online: https://2021.help.altair.com/2021/hwsolvers/os/topics/solvers/os/topology_opt_design_variables_r.htm.

Koutromanos I., McClure J., Roy C. Fundamentals of Finite Element Analysis: Linear Finite Element Analysis. John Wiley & Sons Ltd.; Hoboken, NJ, USA: 2018.

Sefene E.M. State-of-the-art of selective laser melting process: A comprehensive review. J. Manuf. Syst. 2022;63:250–274. doi: 10.1016/j.jmsy.2022.04.002. DOI

DebRoy T., Wei H.L., Zuback J.S., Mukherjee T., Elmer J.W., Milewski J.O., Beese A.M., Wilson-Heid A., De A., Zhang W. Additive manufacturing of metallic components—Process, structure and properties. Prog. Mater. Sci. 2018;92:112–224. doi: 10.1016/j.pmatsci.2017.10.001. DOI

Kruth J., Mercelis P., Van Vaerenbergh J., Froyen L., Rombouts M. Binding mechanisms in selective laser sintering and selective laser melting. Rapid Prototyp. J. 2005;11:26–36. doi: 10.1108/13552540510573365. DOI

Brandt M., Sun S., Leary M., Feih S., Elambasseril J., Liu Q. High-Value SLM Aerospace Components: From Design to Manufacture. Adv. Mater. Res. 2013;633:135–147. doi: 10.4028/www.scientific.net/AMR.633.135. DOI

Venkata K.A., Uppaluri R., Schob B., Zopp C., Kordaß R., Bohlen J., Höfemann M., Kasprowicz M., Pawlak A., Chlebus E. Accurate numerical prediction of thermo-mechanical behaviour and phase fractions in SLM components of advanced high strength steels for automotive applications. Technol. Lightweight Struct. 2022;5:41–50. doi: 10.21935/tls.v5i1.145. DOI

Yadroitsev I., Krakhmalev P., Yadroitsava I. Selective laser melting of Ti6Al4V alloy for biomedical applications: Temperature monitoring and microstructural evolution. J. Alloy. Compd. 2014;583:404–409. doi: 10.1016/j.jallcom.2013.08.183. DOI

Kobir M.H., Yavari R., Riensche A., Bevans B., Castro L., Cole K., Rao P. Prediction of recoater crash in laser powder bed fusion additive manufacturing using graph theory thermomechanical modeling. Prog. Addit. Manuf. 2022 doi: 10.1007/s40964-022-00331-5. DOI

Gogolewski D., Bartkowiak T., Kozior T., Zmarzły P. Multiscale Analysis of Surface Texture Quality of Models Manufactured by Laser Powder-Bed Fusion Technology and Machining from 316L Steel. Materials. 2021;14:2794. doi: 10.3390/ma14112794. PubMed DOI PMC

Liang Z., Hengzhi G., Jingxian X., Yang C., Chunjiang S. Research on Simufact simulation data processing system based on QT and MySQL. Appl. Math. Nonlinear Sci. 2021;6:291–298. doi: 10.2478/amns.2021.2.00042. DOI

Pagac M., Hajnys J., Halama R., Aldabash T., Mesicek J., Jancar L., Jansa J. Prediction of Model Distortion by FEM in 3D Printing via the Selective Laser Melting of Stainless Steel AISI 316L. Appl. Sci. 2021;11:1656. doi: 10.3390/app11041656. DOI

Jia H., Sun H., Wang H., Wu Y., Wang H. Size effect in selective laser melting additive manufacturing of 700 mm large component. J. Manuf. Process. 2022;75:125–137. doi: 10.1016/j.jmapro.2022.01.011. DOI

Xie D., Lv F., Yang Y., Shen L., Tian Z., Shuai C., Chen B., Zhao J. A Review on Distortion and Residual Stress in Additive Manufacturing. Chin. J. Mech. Eng. Addit. Manuf. Front. 2022;1:100039. doi: 10.1016/j.cjmeam.2022.100039. DOI

Adamczak S., Zmarzły P., Kozior T., Gogolewski D. Assessment of Roundness and Waviness Deviations of Elements Produced by Selective Laser Sintering Technology; Proceedings of the 23rd International Conference Engineering Mechanics; Svratka, Czech Republic. 15–18 May 2017.