finite element analysis (FEA) Dotaz Zobrazit nápovědu
Osseointegration is paramount for the longevity of dental implants and is significantly influenced by biomechanical stimuli. The aim of the present study was to assess the micro-strain and displacement induced by loaded dental implants at different stages of osseointegration using finite element analysis (FEA). Computational models of two mandible segments with different trabecular densities were constructed using microCT data. Three different implant loading directions and two osseointegration stages were considered in the stress-strain analysis of the bone-implant assembly. The bony segments were analyzed using two approaches. The first approach was based on Mechanostat strain intervals and the second approach was based on tensile/compression yield strains. The results of this study revealed that bone surrounding dental implants is critically strained in cases when only a partial osseointegration is present and when an implant is loaded by buccolingual forces. In such cases, implants also encounter high stresses. Displacements of partially-osseointegrated implant are significantly larger than those of fully-osseointegrated implants. It can be concluded that the partial osseointegration is a potential risk in terms of implant longevity.
- Klíčová slova
- Dental implants, Micro finite element analysis, Osseointegration, Strain intensity, Stress intensity,
- MeSH
- analýza metodou konečných prvků MeSH
- analýza zatížení zubů metody MeSH
- biologické modely * MeSH
- biomechanika MeSH
- lidé MeSH
- mandibula fyziologie MeSH
- mechanický stres MeSH
- osteointegrace fyziologie MeSH
- počítačové zpracování signálu MeSH
- rentgenová mikrotomografie MeSH
- zubní implantáty * MeSH
- Check Tag
- lidé MeSH
- mužské pohlaví MeSH
- Publikační typ
- časopisecké články MeSH
- práce podpořená grantem MeSH
- Názvy látek
- zubní implantáty * MeSH
The finite element analysis (FEA) has been identified as a useful tool for the stress and strain behaviour determination in lower limb prosthetics. The residual limb and prosthetic socket interface was the main subject of interest in previous studies. This paper focuses on the finite element analysis for the evaluation of structural behaviour of the Sure-flex™ prosthetic foot and other load-bearing components. A prosthetic socket was not included in the FEA. An approach for the finite element modelling including foot analysis, reverse engineering and material property testing was used. The foot analysis incorporated ground reaction forces measurement, motion analysis and strain gauge analysis. For the material model determination, non-destructive laboratory testing and its FE simulation was used. A new, realistic way of load application is presented along with a detailed investigation of stress distribution in the load-bearing components of the prosthesis. A novel approach for numerical and experimental agreement determination was introduced. This showed differences in the strain on the pylon between the experimental and the numerical model within 30% for the anteroposterior bending and up to 25% for the compression. The highest von Mises stresses were found on the foot-pylon connecting component at toe off. Peak stress of 216MPa occurred on the posterior adjusting screw and maximum stress of 156MPa was found at the neck of the male pyramid.
- MeSH
- amputovaní * MeSH
- analýza metodou konečných prvků * MeSH
- dospělí MeSH
- lidé MeSH
- mechanický stres MeSH
- protézy - design MeSH
- protézy a implantáty * MeSH
- tibie * MeSH
- zatížení muskuloskeletálního systému MeSH
- Check Tag
- dospělí MeSH
- lidé MeSH
- mužské pohlaví MeSH
- Publikační typ
- časopisecké články MeSH
- práce podpořená grantem MeSH
PURPOSE OF THE STUDY In this study, our aim is to examine the effect of proximal fibular osteotomy on knee and ankle kinematics with finite element analysis method. MATERIAL AND METHODS One 62-year-old, female volunteer's radiologic images were used for creating lower limb model. Osteotomized model (OM) which was created according to definition of PFO and non-osteotomized model (NOM) were created. To obtain a stress distribution comparison between the two models, 350 N of axial force was applied to the femoral heads of the models. RESULTS After PFO, the average contact pressure decreased 26.1% at the medial tibial cartilage and increased 42.4% at the lateral tibial cartilage. The Von Mises stresses decreased 57.1% at the femoral cartilage and decreased 79.1% at tibial cartilage. The stress on the tibial cartilage increased 44.6%, and stress on the talar cartilage increased 7.1% at the ankle joint. CONCLUSIONS FEA revealed that main loading at the knee joint shifted from medial tibial cartilage to the lateral tibial cartilage after PFO. Additionally, the stresses on each cartilage were redistributed across a wider and more peripheral area. FEA also demonstrated that the Von Mises stresses of the tibial and talar cartilages of the ankle joint increased after PFO. Key words: knee pain, osteoarthritis, osteotomy, finite element analysis, axial loadings.
- MeSH
- analýza metodou konečných prvků MeSH
- biomechanika MeSH
- hlezenní kloub * diagnostické zobrazování chirurgie MeSH
- kolenní kloub * diagnostické zobrazování chirurgie MeSH
- lidé MeSH
- mechanický stres MeSH
- osteotomie MeSH
- tibie diagnostické zobrazování chirurgie MeSH
- Check Tag
- lidé MeSH
- ženské pohlaví MeSH
- Publikační typ
- časopisecké články MeSH
The first aim of this study was to assess displacements and micro-strain induced on different grades of atrophic cortical and trabecular mandibular bone by axially loaded dental implants using finite element analysis (FEA). The second aim was to assess the micro-strain induced by different implant geometries and the levels of bone-to-implant contact (BIC) on the surrounding bone. Six mandibular bone segments demonstrating different grades of mandibular bone atrophy and various bone volume fractions (from 0.149 to 0.471) were imaged using a micro-CT device. The acquired bone STL models and implant (Brånemark, Straumann, Ankylos) were merged into a three-dimensional finite elements structure. The mean displacement value for all implants was 3.1 ±1.2 µm. Displacements were lower in the group with a strong BIC. The results indicated that the maximum strain values of cortical and cancellous bone increased with lower bone density. Strain distribution is the first and foremost dependent on the shape of bone and architecture of cancellous bone. The geometry of the implant, thread patterns, grade of bone atrophy and BIC all affect the displacement and micro-strain on the mandible bone. Preoperative finite element analysis could offer improved predictability in the long-term outlook of dental implant restorations.
- Klíčová slova
- Bone-implant-contact, Dental implant, Finite element analysis, Mandible, Micro-CT,
- MeSH
- analýza metodou konečných prvků * MeSH
- analýza zatížení zubů metody MeSH
- atrofie MeSH
- kosti a kostní tkáň MeSH
- lidé MeSH
- mandibula patologie fyziologie MeSH
- rentgenová mikrotomografie MeSH
- studie proveditelnosti MeSH
- zatížení muskuloskeletálního systému MeSH
- zubní implantáty škodlivé účinky MeSH
- zuby-sanace - selhání * MeSH
- Check Tag
- lidé MeSH
- Publikační typ
- časopisecké články MeSH
- práce podpořená grantem MeSH
- Názvy látek
- zubní implantáty MeSH
STATEMENT OF PROBLEM: Accurate implant placement is essential for the success of dental implants. This placement influences osseointegration and occlusal forces. The freehand technique, despite its cost-effectiveness and time efficiency, may result in significant angular deviations compared with guided implantation, but the effect of angular deviations on the stress-strain state of peri-implant bone is unclear. PURPOSE: The purpose of this finite element analysis (FEA) study was to examine the effects of angular deviations on stress-strain states in peri-implant bone. MATERIAL AND METHODS: Computational modeling was used to investigate 4 different configurations of dental implant positions, each with 3 angles of insertion. The model was developed using computed tomography images, and typical mastication forces were considered. Strains were analyzed using the mechanostat hypothesis. RESULTS: The location of the implant had a significant impact on bone strain intensity. An angular deviation of ±5 degrees from the planned inclination did not significantly affect cancellous bone strains, which primarily support the implant. However, it had a substantial effect on strains in the cortical bone near the implant. Such deviations also significantly influenced implant stresses, especially when the support from the cortical bone was uneven or poorly localized. CONCLUSIONS: In extreme situations, angular deviations can lead to overstraining the cortical bone, risking implant failure from unfavorable interaction with the implant. Accurate implant placement is essential to mitigate these risks.
BACKGROUND: Total knee arthroplasty (TKA) with all-polyethylene tibial (APT) components has shown comparable survivorship and clinical outcomes to that with metal-backed tibial (MBT). Although MBT is more frequently implanted, APT equivalents are considered a low-cost variant for elderly patients. A biomechanical analysis was assumed to be suitable to compare the response of the periprosthetic tibia after implantation of TKA NexGen APT and MBT equivalent. METHODS: A standardised load model was used representing the highest load achieved during level walking. The geometry and material models were created using computed tomography data. In the analysis, a material model was created that represents a patient with osteopenia. RESULTS: The equivalent strain distribution in the models of cancellous bone with an APT component showed values above 1000 με in the area below the medial tibial section, with MBT component were primarily localised in the stem tip area. For APT variants, the microstrain values in more than 80% of the volume were in the range from 300 to 1500 με, MBT only in less than 64% of the volume. CONCLUSION: The effect of APT implantation on the periprosthetic tibia was shown as equal or even superior to that of MBT despite maximum strain values occurring in different locations. On the basis of the strain distribution, the state of the bone tissue was analysed to determine whether bone tissue remodelling or remodelling would occur. Following clinical validation, outcomes could eventually modify the implant selection criteria and lead to more frequent implantation of APT components.
- Klíčová slova
- All-polyethylene tibial component, Computational modeling, FEA, Finite element method, Knee replacement, Metal-backed tibial component, TKR, Total knee arthroplasty,
- MeSH
- analýza metodou konečných prvků MeSH
- kovy MeSH
- lidé MeSH
- polyethylen MeSH
- protézy - design MeSH
- protézy kolene * MeSH
- senioři MeSH
- tibie diagnostické zobrazování chirurgie MeSH
- totální endoprotéza kolene * MeSH
- Check Tag
- lidé MeSH
- senioři MeSH
- Publikační typ
- časopisecké články MeSH
- Názvy látek
- kovy MeSH
- polyethylen MeSH
The objective of this study was to compare the distribution of stress in the maxillary bone, dental implants, and prosthetic components supporting implant-supported maxillary overdentures with partial palatal coverage, in both splinted and unsplinted designs. Two models of maxillary overdentures were designed using the Exocad Dental CAD program, which included cancellous and cortical bone. The complete denture design and abutments (locator abutments in the unsplinted and Hader bar with Vertix attachments placed distally in the splinted variant) were also designed. The denture material was PEEK (Polyetheretherketone), and the method used to analyze patient-specific 3D X-ray scans was 3D QCT/FEA (three-dimensional quantitative computed tomography-based finite element analysis). Loading was divided into three load cases, in the frontal region (both incisors of the denture) and distal region (both molars and first premolar of the denture). The forces applied were 150 N with an oblique component with a buccal inclination of 35° in the frontal region, and 600 N with a buccal inclination of 5° (molars) or solely vertical (premolar) in the distal region. The model with locator abutments showed higher stresses in all load cases in both analyzed implant variants and in the maxilla. The differences in stress distribution between the splinted and unsplinted variants were more significant in the distal region. According to the results of the present study, the amount of stress in bone tissue and dental implant parts was smaller in the splinted, bar-retained variant. The findings of this study can be useful in selecting the appropriate prosthetic design for implant-supported maxillary overdentures with partial palatal coverage.
- Klíčová slova
- FEA, bar-retained overdenture, implant-supported overdenture, locator attachments,
- Publikační typ
- časopisecké články MeSH
Analysis of mechanical and thermal behaviors during braking has become an increasingly important issue in many transport sectors for different modes of transportation. Brake failure generated during braking is a complex phenomenon confronting automobile manufacturers and designers. During braking, kinetic energy is transferred to thermal energy, resulting in the intense heating of disc brake rotors that increases proportionally with vehicle speed, mass, and braking frequency. It is essential to look into and improve strategies to make versatile, thermally resistant, lightweight, high-performance discs. As a result, this study uses the finite element method to conduct a thermo-mechanical analysis of aluminum alloy and aluminum matrix nano-composite disc brake rotors to address the abovementioned issues. The FEA method is used for the thermo-mechanical analysis of AMNCs for vented disc brake rotor during emergency braking at 70 km/h. From the results obtained, aluminum base metal matrix nano-composites have an excellent strength-to-weight ratio when used as disc brake rotor materials, significantly improving the discs' thermal and mechanical performance. From the result of transient thermal analysis, the maximum value of heat flux obtained for aluminum alloy disc is about 8 W/mm2, whereas for AMNCs, the value is increased to 16.28 W/mm2. The result from static analysis shows that the maximum deformation observed is 0.19 mm for aluminum alloy disc and 0.05 mm for AMNCs disc. In addition, the maximum von Mises stress value of AMNC disc is about 184 MPa. The maximum von Mises stress value of aluminum alloy disc is about 180 MPa. Therefore, according to the results, the proposed aluminum base metal matrix nano-composites are valid for replacing existing materials for disc brake rotor applications.
- Klíčová slova
- aluminum alloy, aluminum matrix nano-composites, disc brake, finite element analysis, thermo-mechanical analysis,
- Publikační typ
- časopisecké články MeSH
AIMS: Bone structure around basal implants shows a dual healing mode: direct contact areas manifest primary osteonal remodeling, in the void osteotomy-induced spaces, the repair begins with woven bone formation. This woven bone is later converted into osteonal bone. The purpose of this study was to develop a model to accurately represent the interface between bone and basal implant throughout the healing process. The model was applied to the biological scenario of changing load distribution in a basal implant system over time. METHODS: Computations were made through finite element analysis using multiple models with changing boneimplant contact definitions which reflected the dynamic nature of the interface throughout the bony healing process. Five stages of bony healing were calculated taking into account the changes in mineral content of bone in the vicinity of the load transmitting implant surfaces. RESULTS: As the bony integration of basal implants proceeds during healing, peak stresses within the metal structure shift geographically. While bony repair may still weaken osteonal bone, woven bone has already matured. This leads to changes in the load distribution between and within the direct contact areas, and bone areas which make later contact with implant. CONCLUSIONS: This study shows that basal implants undergo an intrinsic shift of maximum stress regions during osseointegration. Fatigue testing methods in the case of basal implants must therefore take into account this gradual shift from early healing phase until full osseointegration is achieved.
AIM: Bendable and angulated single-piece implants are used alternatively to screwable abutments in two-piece dental implant designs. Though used frequently, data on the stress distribution within such implants are not available and the question whether the bending contributes to fracture resistance has not been addressed. METHODS: We used the method of finite element to identify von Mises stresses and maximum stresses in bent and non-bent but angulated implants. Implants with one (e.g. applicable to screw designs) or two (applicable to basal implants) bending areas were the variables under investigation. RESULTS: For bends up to 13 degrees we discovered that if there is only one bend, the maximum stress is in the bent area. If two bends are made in two different bending areas, the maximum stresses are distributed between the two and, if either one of the bent areas is machined, there are no residual stresses within the implant body in this area. The maximum stresses are always located near the base-plates. The absolute value of the maximum stress is higher because no residual stresses are available to compensate stresses that stem from loading. CONCLUSION: Assuming that all other parameters are equal, bendable (basal) implants show a more even stress distribution along the vertical implant region than identically shaped implants with a machine-angulated area. Bendable basal implants therefore probably resist masticatory forces better than pre-angulated, machined implants, and unbent implants which provide a thin region in the vertical implant area.
- MeSH
- analýza metodou konečných prvků MeSH
- analýza zatížení zubů * MeSH
- lidé MeSH
- pružnost MeSH
- techniky in vitro MeSH
- titan MeSH
- zubní implantáty * MeSH
- zubní materiály * MeSH
- Check Tag
- lidé MeSH
- Publikační typ
- časopisecké články MeSH
- práce podpořená grantem MeSH
- srovnávací studie MeSH
- Názvy látek
- titan MeSH
- zubní implantáty * MeSH
- zubní materiály * MeSH
