Powdered samples of new and old gasoline catalysts (Pt, Pd, Rh) and new and old diesel (Pt) catalysts were subjected to a pH-static leaching procedure (pH 2-9) coupled with thermodynamic modeling using PHREEQC-3 to verify the release and mobility of PGEs (platinum group elements). PGEs were released under acidic conditions, mostly exhibiting L-shaped leaching patterns: diesel old: 5.47, 0.005, 0.02; diesel new: 68.5, 0.23, 0.11; gasoline old: 0.1, 11.8, 4.79; gasoline new 2.6, 25.2, 35.9 in mg kg(-1) for Pt, Pd and Rh, respectively. Only the new diesel catalyst had a strikingly different leaching pattern with elevated concentrations at pH 4, probably influenced by the dissolution of the catalyst carrier and washcoat. The pH-static experiment coupled with thermodynamic modeling was found to be an effective instrument for understanding the leaching behavior of PGEs under various environmental conditions, and indicated that charged Pt and Rh species may be adsorbed on the negatively charged surface of kaolinite or Mn oxides in the soil system, whereas uncharged Pd and Rh species may remain mobile in soil solutions.
An amorphous Mn oxide (AMO), nanomaghemite, and nanomagnetite were used as potential amendments reducing the mobility of As in three contrasting contaminated soils differing in origin of As contamination. Adsorption experiments and XPS analyses combined with incubation batch experiments and pH-static leaching tests were used. The AMO showed excellent adsorption capacity for As(V) reaching a maximum of 1.79 mmol g(-1) at pH 7 and 8. Interestingly, the adsorption capacity in this case decreases with decreasing pH, probably as a result of AMO dissolution at lower pH values. Chemical sorption of As(V) onto AMO was further confirmed with XPS. Both Fe nano-oxides proved the highest adsorption capacity at pH 4 reaching 11 mg g(-1) of adsorbed As(V). The AMO was also the most efficient amendment for decreasing As concentrations in soil solutions during 8 weeks of incubation. Additionally, pH-static leaching tests were performed at pH 4, 5, 6, 7, and natural pH (not adjusted) and AMO again proved the highest ability to decrease As content in leachate. On the other hand, strong dissolution of this amendment at lower pH values (especially pH 4) was observed. For that reason, AMO appears as a promising stabilizing agent for As, especially in neutral, alkaline, or slightly acidic soils, where As(V) species are expected to be more mobile.
- MeSH
- Adsorption MeSH
- Arsenic analysis chemistry MeSH
- Kinetics MeSH
- Hydrogen-Ion Concentration MeSH
- Soil Pollutants analysis chemistry MeSH
- Nanoparticles chemistry MeSH
- Oxides chemistry MeSH
- Soil chemistry MeSH
- Environmental Restoration and Remediation MeSH
- Manganese Compounds chemistry MeSH
- Ferric Compounds chemistry MeSH
- Environmental Pollution analysis MeSH
- Publication type
- Journal Article MeSH
An amorphous manganese oxide (AMO) and a Pb smelter-polluted agricultural soil amended with the AMO and incubated for 2 and 6 months were subjected to a pH-static leaching procedure (pH 3-8) to verify the chemical stabilization effect on metals and metalloids. The AMO stability in pure water was pH-dependent with the highest Mn release at pH 3 (47% dissolved) and the lowest at pH 8 (0.14% dissolved). Secondary rhodochrosite (MnCO3) was formed at the AMO surfaces at pH>5. The AMO dissolved significantly less after 6 months of incubation. Sequential extraction analysis indicated that "labile" fraction of As, Pb and Sb in soil significantly decreased after AMO amendment. The pH-static experiments indicated that no effect on leaching was observed for Cd and Zn after AMO treatments, whereas the leaching of As, Cu, Pb and Sb decreased down to 20%, 35%, 7% and 11% of the control, respectively. The remediation efficiency was more pronounced under acidic conditions and the time of incubation generally led to increased retention of the targeted contaminants. The AMO was found to be a promising agent for the chemical stabilization of polluted soils.
- MeSH
- Arsenic chemistry MeSH
- Metallurgy MeSH
- Hydrogen-Ion Concentration MeSH
- Soil Pollutants chemistry MeSH
- Waste Management MeSH
- Oxides chemistry MeSH
- Industrial Waste MeSH
- Environmental Restoration and Remediation MeSH
- Manganese Compounds chemistry MeSH
- Metals, Heavy chemistry MeSH
- Publication type
- Journal Article MeSH
- Research Support, Non-U.S. Gov't MeSH
Soils in the vicinity of nonferrous metal smelters are often highly polluted by inorganic contaminants released from particulate emissions. We used a technique with double polyamide experimental bags (1-μm mesh) to study the in situ transformation of fly ash (FA) from a secondary Pb smelter in acidic soil profiles. Between 62 and 66% of the FA dissolved after one year's exposure in the soils, leading to complete dissolution of primary caracolite (Na(3)Pb(2)(SO(4))(3)Cl) and KPb(2)Cl(5), with formation of secondary anglesite (PbSO(4)), minor PbSO(3), and trace carbonates. Release of Pb was pH-dependent, whereas not for Cd and Zn. Significant amounts of metals (mainly Cd and Zn) partitioned into labile soil fractions. The field data agreed with laboratory pH-static leaching tests performed on FA, which was washed before the experiment to remove soluble salts. This indicates that appropriate laboratory leaching can accurately predict FA behavior in real-life scenarios (e.g., exposure in soil).
The leaching behaviors of primary copper (Cu) slags originating from Ausmelt, reverbatory, and converter furnaces operating under a single technological process were compared to a residual slag tailing obtained by slag re-processing via flotation and metal recovery. The EN 12457-2 leaching test, used for assessment of the hazardous properties, was followed by the CEN/TS 14997 pH-static leaching test (pH range 3-12). Both leaching experiments were coupled with a mineralogical investigation of the primary and secondary phases as well as geochemical modeling. Metals (Cd, Cu, Pb, Zn) exhibit the highest leaching at low pH. Under acidic conditions (pH 3-6), Ausmelt slag and slag tailing exhibited higher metal leaching compared to other slag types. Very low leaching of metals (far below EU limits for non-hazardous waste) was observed at natural pH (7.9-9.0) for all the studied slag samples. In contrast, relatively high leaching of As was observed over the entire pH range, especially for Ausmelt slag (exceeding the EU limit for hazardous waste by 1.7×). However, geochemical modeling and scanning electron microscopy indicated that formation of stable Ca-Cu-Pb arsenates and the binding of As to newly formed Fe (oxyhydr)oxides play an important role in efficient As immobilization at the slag-water interface. In contrast, no controls were predicted for Sb, whose leaching was almost pH-independent. Nevertheless Sb leached concentrations at natural pH were below EU limit for hazardous waste. Re-processing of primary Cu slags for metal recovery, and subsequent co-disposal of the resulting slag tailing with dolomite-rich mine tailing and local laterite is suitable for stabilizing the remaining contaminants (except Sb) and limiting their leaching into the environment.
- MeSH
- Arsenates MeSH
- European Union MeSH
- Mining MeSH
- Metallurgy methods MeSH
- Metals MeSH
- Environmental Pollutants analysis MeSH
- Copper * MeSH
- Hazardous Waste legislation & jurisprudence MeSH
- Waste Products analysis MeSH
- Environment * MeSH
- Publication type
- Journal Article MeSH
- Geographicals
- Namibia MeSH
Currently standardised leaching tests require grain size reduction, which for large fragments of slags could overestimate the leaching results. To assess the effect of the fine-grained fraction generated by sample crushing, a set of leaching experiments was performed on copper smelting slag from the Zambian Copperbelt: (i) EN 12457-2 batch tests (standardised grain size <4 mm; modified procedure with grain size of 4-0.5 mm simulating exposure of larger fragments on the dumps) and (ii) CEN/TS 14997 pH-static tests (standardised grain size <1 mm simulating the possible wind dispersion scenario near the slag crushing facilities or disposal of fine-grained granulated slag; additional grain sizes <5 mm, 5-0.5 mm and 5-0.5 mm after ultrasonic cleaning). A higher proportion of the fine-grained fraction generally led to greater leaching of Cu, Co and Zn. The metal levels in the leachates under circum-neutral conditions were all below the EU limits for non-hazardous waste. However, at pH 4, the presence of fine dust particles dramatically increased the concentrations of metals in the slag leachates. The greater leachability of Cu and Co from slag particles under acidic conditions suggests a risk of their mobilisation in acidic soils in the Copperbelt area.
- MeSH
- Copper chemistry toxicity MeSH
- Publication type
- Journal Article MeSH
- Research Support, Non-U.S. Gov't MeSH
Electrochemical conversion of fesoterodine to one of its oxidation products was evaluated with the application of the wall-jet flow cell. A traditional, "static" mode of electrolysis was compared with the "dynamic" mode of cell performance. For statistical assessment of the data, experiments were planned and performed with the application of design of experiments approach, namely Taguchi L18 design. After screening phase, the experimental settings were broadened or adjusted according to the results and optimization was performed. All of the samples were electrolysed with the use of chronoamperometric method in a three electrode system. The electrolysed samples were analysed using UHPLC-PDA-QDA method. The chromatographic run was performed in gradient elution with the application of C8 column. The response was expressed as % area of the main peak found with the PDA detection method whereas QDA detector was used in positive SIM mode for structural confirmation. All data obtained for both screening and optimization were treated together and linear models were adjusted. The use of large-surface glassy carbon electrode along with pH~7 were found to be the most significant factors influencing electrochemical oxidation of fesoterodine in both modes. The major differences were identified in terms of voltage applied to the electrodes which yielded the highest amounts of oxidation product. Evolution of electrochemical methods may serve as complementary technique in stress degradation studies in pharmaceutical industry.
... Membrane During Their Translation -- Direct Evidence Favoring Vectorial Discharge Has Come from Experiments ... ... Between the Kinetochore and Polar Spindle Fibers -- Metaphase Chromosomes Are Held in a Deceptively Static ... ... Increase in Intracellular Free Ca2 + Initiates Egg -- Development 807 -- A Rise in the Intracellular pH ... ... Differentiate Overtly -- The Time of Cell Determination Can Be Discovered by -- Transplantation Experiments ...
xxxix, 1146 s. : il., tab. ; 28 cm
- MeSH
- Cell Biology MeSH
- Molecular Biology MeSH
- Publication type
- Monograph MeSH
- Conspectus
- Biochemie. Molekulární biologie. Biofyzika
- NML Fields
- biologie
- cytologie, klinická cytologie
