Titanium beta alloys represent the new generation of materials for the manufacturing of joint implants. Their Young's modulus is lower and thus closer to the bone tissue compared to commonly used alloys. The surface tribological properties of these materials should be improved by ion implantation. The influence of this surface treatment on corrosion behaviour is unknown. The surface of Ti-36Nb-6Ta, Ti-36Nb-4Zr, and Ti-39Nb titanium β-alloys was modified using nitrogen ion implantation. X-ray photoelectron spectroscopy was used for surface analysis, which showed the presence of titanium, niobium, and tantalum nitrides in the treated samples and the elimination of less stable oxides. Electrochemical methods, electrochemical impedance spectra, polarisation resistance, and Mott-Schottky plot were measured in a physiological saline solution. The results of the measurements showed that ion implantation does not have a significant negative effect on the corrosion behaviour of the material. The best results of the alloys investigated were achieved by the Ti-36Nb-6Ta alloy. The combination of niobium and tantalum nitrides had a positive effect on the corrosion resistance of this alloy. After surface treatment, the polarization resistance of this alloy increased, 2.3 × 106 Ω·cm2, demonstrating higher corrosion resistance of the alloy. These results were also supported by the results of electrochemical impedance spectroscopy.

• Keywords
• corrosion, nitrides, nitrogen ion implantation, titanium alloy,
• MeSH
• Electrochemical Techniques MeSH
• Corrosion MeSH
• Niobium chemistry   MeSH
• Surface Properties MeSH
• Alloys * chemistry   MeSH
• Tantalum chemistry   MeSH
• Materials Testing MeSH
• Titanium * chemistry   MeSH
• Publication type
• Journal Article MeSH
• Names of Substances
• Niobium MeSH
• Alloys * MeSH
• Tantalum MeSH
• Titanium * MeSH

TiMoZrTaSi alloys appertain to a new generation of metallic biomaterials, labeled high-entropy alloys, that assure both biocompatibility as well as improved mechanical properties required by further medical applications. This paper presents the use of nondestructive evaluation techniques for new type of alloys, TiMo20Zr7Ta15Six, with x = 0; 0.5; 0.75; 1.0, which were obtained by vacuum melting. In Ti alloys, the addition of Mo improves tensile creep strength, Si improves both the creep and oxidation properties, Zr leads to an α crystalline structure, which increases the mechanical strength and assures a good electrochemical behavior, and Ta is a β stabilizer sustaining the formation of solid β-phases and contributes to tensile strength improvement and Young modulus decreasing. The effects of Si content on the mechanical properties of the studied alloys and the effect of the addition of Ta and Zr under the presence of Si on the evolution of crystallographic structure was studied. The influence of composition on fracture behavior and strength was evaluated using X-ray diffraction, resonant ultrasound spectroscopy (RUS) analyses, SEM with energy dispersive X-ray spectroscopy, and acoustic emission (AE) within compression tests. The β-type TiMo20Zr7Ta15Six alloys had a good compression strength of over 800 MPa, lower Young modulus (69.11-89.03 GPa) and shear modulus (24.70-31.87 GPa), all offering advantages for use in medical applications.

• Keywords
• acoustic emission, inhomogeneities, mechanical properties, microstructure, resonant ultrasound spectroscopy, titanium alloys,
• Publication type
• Journal Article MeSH

Beta titanium alloy Ti-35Nb-6Ta-7Zr-0.7O (wt%) was developed as a material intended for the manufacturing of a stem of a hip joint replacement. This alloy contains only biocompatible elements and possesses a very high yield strength already in the cast condition (900 MPa). However, the porosity, large grain size and chemical inhomogeneity reduce the fatigue performance below the limits required for utilization in the desired application. Two methods of hot working, die forging and hot rolling, were used for processing of this alloy. Microstructural evolution, tensile properties and fatigue performance of the hot worked material were investigated and compared to the cast material. Microstructural observations revealed that porosity is removed in all hot-worked conditions and the grain size is significantly reduced when the area reduction exceeds 70%. Static tensile properties were improved by both processing methods and ultimate tensile strength (UTS) of 1200 MPa was achieved. Fatigue results were more reproducible in the hot rolled material due to better microstructural homogeneity, but forging leads to an improved fatigue performance. Fatigue limit of 400 MPa was achieved in the die-forged condition after 70% of area reduction and in the hot rolled condition after 86% of area reduction.

• Keywords
• biomedicine, fatigue testing, hot working, tensile testing, titanium alloys,
• Publication type
• Journal Article MeSH