We report here on the development of tailored plasmonic AgNPs/C:H:N:O plasma polymer nanocomposites for the detection of the pathogenic bacterium Borrelia afzelii , with high selectivity and sensitivity. Silver (Ag) nanoparticles, generated by a gas aggregation source, are incorporated onto a C:H:N:O plasma polymer matrix, which is deposited by magnetron sputtering of a nylon 6.6. These anchored Ag nanoparticles propagate localized surface plasmon resonance (LSPR), optically responding to changes caused by immobilized pathogens near the nanoparticles. The tailored functionalization of AgNPs/C:H:N:O nanocomposite surface allows both high selectivity for the pathogen and high sensitivity with an LSPR red-shift Δλ > (4.20 ± 0.71) nm for 50 Borrelia per area 0.785 cm2. The results confirmed the ability of LSPR modulation for the rapid and early detection of (not only) tested pathogens.

• Klíčová slova
• C:H:N:O thin film, Lyme disease, ag nanoparticles, borrelia, localized surface plasmon resonance, magnetron sputtering, nanocomposite, nylon, plasma polymer, surface functionalization,
• MeSH
• kovové nanočástice * chemie   MeSH
• limita detekce * MeSH
• nanokompozity * chemie   MeSH
• povrchová plasmonová rezonance * metody   MeSH
• stříbro * chemie   MeSH
• Publikační typ
• časopisecké články MeSH
• Názvy látek
• stříbro * MeSH

In this work, we demonstrate, for the first time, the possibility to fabricate indium tin oxide nanoparticles (ITO NPs) using a gas aggregation cluster source. A stable and reproducible deposition rate of ITO NPs has been achieved using magnetron sputtering of an In2O3/SnO2 target (90/10 wt %) at an elevated pressure of argon. Remarkably, most of the generated NPs possess a crystalline structure identical to the original target material, which, in combination with their average size of 17 nm, resulted in a localized surface plasmon resonance peak at 1580 nm in the near-infrared region.

• Publikační typ
• časopisecké články MeSH

The physicochemical and mechanical properties of thin and freestanding heavy boron-doped diamond (BDD) nanosheets coated with a thin C:H:N:O plasma polymer were studied. First, diamond nanosheets were grown and doped with boron on a Ta substrate using the microwave plasma-enhanced chemical vapor deposition technique (MPECVD). Next, the BDD/Ta samples were covered with nylon 6.6 to improve their stability in harsh environments and flexibility during elastic deformations. Plasma polymer films with a thickness of the 500-1000 nm were obtained by magnetron sputtering of a bulk target of nylon 6.6. Hydrophilic nitrogen-rich C:H:N:O was prepared by the sputtering of nylon 6.6. C:H:N:O as a film with high surface energy improves adhesion in ambient conditions. The nylon-diamond interface was perfectly formed, and hence, the adhesion behavior could be attributed to the dissipation of viscoelastic energy originating from irreversible energy loss in soft polymer structure. Diamond surface heterogeneities have been shown to pin the contact edge, indicating that the retraction process causes instantaneous fluctuations on the surface in specified microscale regions. The observed Raman bands at 390, 275, and 220 cm-1 were weak; therefore, the obtained films exhibited a low level of nylon 6 polymerization and short-distance arrangement, indicating crystal symmetry and interchain interactions. The mechanical properties of the nylon-on-diamond were determined by a nanoindentation test in multiload mode. Increasing the maximum load during the nanoindentation test resulted in a decreased hardness of the fabricated structure. The integration of freestanding diamond nanosheets will make it possible to design flexible chemical multielectrode sensors.

• Klíčová slova
• diamond composite, magnetron sputtering, nanoindentation, nylon 6.6, optical constants,
• Publikační typ
• časopisecké články MeSH