Volumetric shrinkage (VS) of conventional, bulk-fill, and core build-up resin-based composites (RBCs) of various thickness (1-5 mm) was measured using the modified bonded-disk method with confocal laser scanning microscopy. Additionally, the bottom-to-top ratio of Vickers hardness (%VH) was measured. Conventional RBCs exhibited significantly higher VS than bulk-fill and core build-up RBCs (p<0.05). As specimen thickness increased, VS relative to volume (%VS) and difference in VS at each depth (VSdepth) decreased. For conventional RBCs, there was a significant drop in VSdepth between 1 mm and 2 mm (p<0.05), and another drop was observed between 3 mm and 4 mm (p<0.05) where %VH decreased below 90%. For bulk-fill and core build-up RBCs, VSdepth decreased significantly between 2 mm and 3 mm (p<0.05), but %VH exceeded 90% even in 5 mm deep cavities. These results indicated that post-curing contributed to lower shrinkage in deeper layers, and that conventional RBCs were not adequately polymerized at the depth of over 3 mm.
The effect of warm air-blowing on the sealing ability of two one-bottle and one two-bottle silane-containing universal adhesives (UAs) applied to lithium disilicate ceramics (LDS) was evaluated. Tapered cavities prefabricated in LDS blocks (IPS e.max CAD) were treated by the adhesives, air-blown either with normal air (23±1°C) or warm air (60±5°C), and filled with a flowable resin composite. Interfacial gap formation was observed using swept-source optical coherence tomography immediately after filling, after 24 h, 5,000 and 10,000 thermal cycles, and an additional 1-year water storage. Specimens bonded using normal air-blown one-bottle UAs exhibited a significantly higher gap formation than the two-bottle UA (p<0.001), and detached within 24 h. Warm air-blowing significantly decreased the gap formation of one-bottle UAs (p<0.001), but the specimens dislocated within 24 h or during thermocycling. The two-bottle UA withstood all aging procedures and warm air-blowing significantly decreased its 1-year gap formation compared to normal air-blowing (p=0.002).
OBJECTIVES: To evaluate the sealing performance of self-etch adhesives (SEA) after smear layer deproteinization with chemo-mechanical caries removal agents (CRA) to enamel and dentin cavity walls in comparison with 6% NaOCl smear layer deproteinizing. METHODS: Eighty extracted bovine incisors with tapered cylindrical cavities (2.5 mm upper diameter, 1.5 mm lower diameter, 2 mm depth) at the cemento-enamel junction were randomly divided into four pre-treatment groups; no treatment (control), Papacarie (papain enzyme-based CRA), Carisolv (NaOCl-based CRA), and 6% NaOCl. After pretreatment, G-Bond Plus (GBP, one-step SEA) or Clearfil SE Bond 2 (CSE, two-step SEA) was applied to the pre-treated cavity, and then filled with a flowable resin composite (Clearfil Majesty ES Flow). Gap formations at the enamel and dentin lateral walls, and on the dentin cavity floor were investigated using swept-source optical coherence tomography (SS-OCT) after 24-h water storage at 37 °C. Deproteinizing effects of the tested agents on smear layer-covered enamel and dentin were quantified by changes in the amide:phosphate ratio using ATR-FTIR analysis. RESULTS: Papacarie significantly reduced gap formation with both self-etch adhesives at all locations, compared to the control group (p < 0.05). In contrast, increased gap formation was observed with Carisolv and NaOCl. In most groups, CSE exhibited significantly lower gap formation than GBP (p < 0.05). ATR-FTIR revealed a significant decrease in the amide:phosphate ratio for all the deproteinizing agents (p < 0.05). CONCLUSIONS: Chemo-mechanical CRAs could effectively remove the organic phase of enamel and dentin smear layer. The papain enzyme-based gel Papacarie could improve the sealing performance of the self-etch adhesives to both enamel and dentin.
- MeSH
- adheziva MeSH
- dentin MeSH
- dentinová adheziva MeSH
- pryskyřičné cementy MeSH
- skot MeSH
- složené pryskyřice MeSH
- smear layer * MeSH
- testování materiálů MeSH
- vazba zubní * MeSH
- zubní cementy MeSH
- zubní sklovina MeSH
- zvířata MeSH
- Check Tag
- skot MeSH
- zvířata MeSH
- Publikační typ
- časopisecké články MeSH
- práce podpořená grantem MeSH
