The photocatalytic reduction of CO2 with H2O was investigated using Cu/TiO2 photocatalysts in aqueous solution. For this purpose, Cu/TiO2 photocatalysts (with 0.2, 0.9, 2, 4, and 6 wt.% of Cu) have been synthesized via sol-gel method. The photocatalysts were extensively characterized by means of inductively coupled plasma optical emission spectrometry (ICP-OES), N2 physisorption (BET), XRD, UV-vis DRS, FT-IR, Raman spectroscopy, TEM-EDX, and photoelectrochemical measurements. The as-prepared photocatalysts contain anatase as a major crystalline phase with a crystallite size around 13 nm. By increasing the amount of Cu, specific surface area and band gap energy decreased in addition to the formation of large agglomeration of CuO. Results revealed that the photocatalytic reduction of CO2 decreased in the presence of Cu/TiO2 in comparison to pure TiO2, which might be associated to the formation of CuO phase acting as a recombination center of generated electron-hole pair. Decreasing of photoactivity can also be connected with a very low position of conduction band of photocatalysts with high Cu content, which makes H2 production necessary for CO2 reduction more difficult.

• Klíčová slova
• CH4, CO2 reduction, Cu/TiO2, Photocatalysis,
• MeSH
• chemické modely MeSH
• difrakce rentgenového záření MeSH
• fotochemické procesy * MeSH
• katalýza MeSH
• měď chemie   MeSH
• oxid uhličitý chemie   MeSH
• Ramanova spektroskopie MeSH
• spektroskopie infračervená s Fourierovou transformací MeSH
• titan chemie   MeSH
• Publikační typ
• časopisecké články MeSH
• Názvy látek
• měď MeSH
• oxid uhličitý MeSH
• titan MeSH
• titanium dioxide MeSH Prohlížeč

TiO2 aerogels doped with Ni, Co, Cu, and Fe were prepared, and their structure and photocatalytic activity during the decomposition of a model pollutant, acid orange (AO7), were studied. After calcination at 500 °C and 900 °C, the structure and composition of the doped aerogels were evaluated and analyzed. XRD analysis revealed the presence of anatase/brookite and rutile phases in the aerogels along with other oxide phases from the dopants. SEM and TEM microscopy showed the nanostructure of the aerogels, and BET analysis showed their mesoporosity and high specific surface area of 130 to 160 m2·g-1. SEM-EDS, STEM-EDS, XPS, EPR methods and FTIR analysis evaluated the presence of dopants and their chemical state. The concentration of doped metals in aerogels varied from 1 to 5 wt.%. The photocatalytic activity was evaluated using UV spectrophotometry and photodegradation of the AO7 pollutant. Ni-TiO2 and Cu-TiO2 aerogels calcined at 500 °C showed higher photoactivity coefficients (kaap) than aerogels calcined at 900 °C, which were ten times less active due to the transformation of anatase and brookite to the rutile phase and the loss of textural properties of the aerogels.

• Klíčová slova
• aerogels, anatase, brookite, photocatalytic properties, transition metal ions,
• Publikační typ
• časopisecké články MeSH

TiO2 as nanostructured powders were prepared by (1) sol-gel process and (2) hydrothermal method in combination with (A) the processing by pressurized hot water and methanol or (B) calcination. The subsequent synthesis step was the modification of prepared nanostructured TiO2 with nitrogen using commercial urea. Textural, structural, surface and optical properties of prepared TiO2 and N/TiO2 were characterized by nitrogen physisorption, powder X-ray diffraction, X-ray photoelectron spectroscopy and DR UV-vis spectroscopy. It was revealed that TiO2 and N/TiO2 processed by pressurized fluids showed the highest surface areas. Furthermore, all prepared materials were the mixtures of major anatase phase and minor brookite phase, which was in nanocrystalline or amorphous (as nuclei) form depending on the applied preparation method. All the N/TiO2 materials exhibited enhanced crystallinity with a larger anatase crystallite-size than undoped parent TiO2. The photocatalytic activity of the prepared TiO2 and N/TiO2 was tested in the photocatalytic reduction of CO2 and the photocatalytic decomposition of N2O. The key parameters influencing the photocatalytic activity was the ratio of anatase-to-brookite and character of brookite. The optimum ratio of anatase-to-brookite for the CO2 photocatalytic reduction was determined to be about 83 wt.% of anatase and 17 wt.% of brookite (amorphous-like) (TiO2-SG-C). The presence of nitrogen decreased a bit the photocatalytic activity of tested materials. On the other hand, TiO2-SG-C was the least active in the N2O photocatalytic decomposition. In the case of N2O photocatalytic decomposition, the modification of TiO2 crystallites surface by nitrogen increased the photocatalytic activity of all investigated materials. The maximum N2O conversion (about 63 % after 18 h of illumination) in inert gas was reached over all N/TiO2.

• Publikační typ
• časopisecké články MeSH

In the majority of photocatalytic applications, the photocatalyst is dispersed as a suspension of nanoparticles. The suspension provides a higher surface for the photocatalytic reaction in respect to immobilized photocatalysts. However, this implies that recovery of the particles by filtration or centrifugation is needed to collect and regenerate the photocatalyst. This complicates the regeneration process and, at the same time, leads to material loss and potential toxicity. In this work, a new nanofibrous membrane, g-C3N4/PMMA/PUR, was prepared by the fixation of exfoliated g-C3N4 to polyurethane nanofibers using thin layers of poly(methyl methacrylate) (PMMA). The optimal amount of PMMA was determined by measuring the adsorption and photocatalytic properties of g-C3N4/PMMA/PUR membranes (with a different PMMA content) in an aqueous solution of methylene blue. It was found that the prepared membranes were able to effectively adsorb and decompose methylene blue. On top of that, the membranes evinced a self-cleaning behavior, showing no coloration on their surfaces after contact with methylene blue, unlike in the case of unmodified fabric. After further treatment with H2O2, no decrease in photocatalytic activity was observed, indicating that the prepared membrane can also be easily regenerated. This study promises possibilities for the production of photocatalytic membranes and fabrics for both chemical and biological contaminant control.

• Klíčová slova
• exfoliated carbon nitride, immersion coating, membrane, photocatalysis, poly(methyl methacrylate), polymers, polyurethane nanofibers, self-cleaning surfaces,
• Publikační typ
• časopisecké články MeSH

Nanotechnology is one of the most impressive sciences in the twenty-first century. Not surprisingly, nanoparticles/nanomaterials have been widely deployed given their multifunctional attributes and ease of preparation via environmentally friendly, cost-effective, and simple methods. Although there are assorted optimized preparative methods for synthesizing the nanoparticles, the main challenge is to find a comprehensive method that has multifaceted properties. The goal of this study has been to synthesize aminated (nano)particles via the Rosmarinus officinalis leaf extract-mediated copper oxide; this modification leads to the preparation of (nano)particles with promising biological and photocatalytic applications. The synthesized NPs have been fully characterized, and biological activity was evaluated in antibacterial assessment against Bacillus cereus as a model Gram-positive and Pseudomonas aeruginosa as a model Gram-negative bacterium. The bio-synthesized copper oxide (nano)particles were screened by MTT assay by applying the HEK-293 cell line. The aminated (nano)particles have shown lower cytotoxicity (~ 21%), higher (~ 50%) antibacterial activity, and a considerable increase in zeta potential value (~ + 13.4 mV). The prepared (nano)particles also revealed considerable photocatalytic activity compared to other studies wherein the dye degradation process attained 97.4% promising efficiency in only 80 min and just 7% degradation after 80 min under dark conditions. The biosynthesized copper oxide (CuO) (nano)particle's biomedical investigation underscores an eco-friendly synthesis of (nano)particles, their noticeable stability in the green reaction media, and impressive biological activity.

• MeSH
• aminace MeSH
• antibakteriální látky metabolismus   farmakologie   MeSH
• bioinženýrství MeSH
• HEK293 buňky MeSH
• kovové nanočástice * MeSH
• lidé MeSH
• měď * farmakologie   MeSH
• oxidy MeSH
• poréznost MeSH
• Check Tag
• lidé MeSH
• Publikační typ
• časopisecké články MeSH
• práce podpořená grantem MeSH
• Názvy látek
• antibakteriální látky MeSH
• cupric oxide MeSH Prohlížeč
• měď * MeSH
• oxidy MeSH

Zinc sulfide (ZnS) nanoparticles were prepared by homogeneous hydrolysis of zinc sulfate and thioacetamide (TAA) at 80 degrees C. After annealing at a temperature above 400 degrees C in oxygen atmosphere, zinc oxide (ZnO) nanoparticles were obtained. The ZnS and ZnO nanoparticles were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), and Brunauer-Emmett-Teller (BET)/Barrett-Joyner-Halenda (BJH) methods were used for surface area and porosity determination. The photocatalytic activity of as-prepared zinc oxide samples was determined by decomposition of Orange II dye in aqueous solution under UV irradiation of 365 nm wavelength. Synthesized ZnO were evaluated for their non-photochemical degradation ability of chemical warfare agents to nontoxic products.

• Publikační typ
• časopisecké články MeSH

Nanometric thin films were prepared by dip-coating and inkjet printing ZnO nanosheets on glass plates. The side-by-side alignment of the ZnO nanosheets on the substrate resulted in thin, transparent, oriented ZnO surfaces with the high-energy {001} facets exposed. The method of nanosheet deposition affected the film morphology; the dip-coated films were very smooth and nonporous, while the inkjet-printed films were rough and porous with the estimated void volume approximately 60-70% of the total film volume. The first-order rate constants for the photocatalytic degradation of 4-chlorophenol on the nanosheet-based films were approximately 2 times larger than those on nanocolumnar ZnO films or ZnO films prepared by the sol-gel technique. We attribute the high photocatalytic activity of the ZnO nanosheets to the fact that their {001} facets were predominantly exposed to the oxidized substrate. This surface arrangement and the simplicity of fabricating the ZnO nanosheet-based films make them promising for the construction of optical devices and dye-sensitized solar cells.

• Publikační typ
• časopisecké články MeSH

Lanthanum-modified TiO2 photocatalysts (0.2-1.5 wt% La) were investigated in the methanol decomposition in an aqueous solution. The photocatalysts were prepared by the common sol-gel method followed by calcination. The structural (X-ray diffraction, Raman, X-ray photoelectron spectroscopy), textural (N2 physisorption), and optical properties (diffuse reflectance spectroscopy, photoelectrochemical measurements) of all synthetized nanomaterials were correlated with photocatalytic activity. Both pure TiO2 and La-doped TiO2 photocatalysts proved higher yields of hydrogen in comparison to photolysis. The photocatalyst with optimal amount of lanthanum (0.2 wt% La) showed almost two times higher amount of hydrogen produced at the same time as in the presence of pure TiO2. The photocatalytic activity increased with both increasing photocurrent response and decreasing amount of lattice and surface O species. It has been shown that both direct and indirect mechanisms of methanol photocatalytic oxidation participate in the production of hydrogen. Both direct and indirect mechanisms take part in the formation of hydrogen.

• Klíčová slova
• La/TiO2, Lattice O species, Methanol oxidation, Photocurrent response, Surface O species,
• MeSH
• chemické látky znečišťující vodu chemie   MeSH
• difrakce rentgenového záření MeSH
• fotochemické procesy * MeSH
• fotoelektronová spektroskopie MeSH
• fotolýza MeSH
• katalýza MeSH
• lanthan chemie   MeSH
• methanol chemie   MeSH
• titan chemie   MeSH
• vodík chemie   MeSH
• Publikační typ
• časopisecké články MeSH
• Názvy látek
• chemické látky znečišťující vodu MeSH
• lanthan MeSH
• methanol MeSH
• titan MeSH
• titanium dioxide MeSH Prohlížeč
• vodík MeSH

This work deals with the preparation of TiO2 nanoparticulate layers of various mass (0.05 mg/cm2 to 2 mg/cm2) from three commercial nanopowder materials, P90, P25 and CG 300, their characterisation (profilometry, BET and SEM) and evaluation of their photocatalytic activity in the gaseous phase in a flow-through photoreactor according to the ISO standard (ISO 22197-2). Hexane was chosen as a single model pollutant and a mixture of four compounds, namely acetaldehyde, acetone, heptane and toluene was used for the evaluation of the efficiency of simultaneous removal of several pollutants. A linear dependence between the layer mass and the layer thickness for all materials was found. Up to a layer mass 0.5 mg/cm2, the immobilisation P90 and P25 powder did not result in a decrease in BET surface area, whereas with an increase in layer mass to 1 mg/cm2, a decrease of the BET surface was observed, being more significant in the case of P90. The photocatalytic conversion of hexane was comparable for all immobilised powders up to a layer mass of 0.5 mg/cm2. For higher layer mass, the photocatalytic conversion of hexane on P25 and P90 differ; the latter achieved about 30% higher conversion. In the case of the simultaneous degradation of four compounds, acetaldehyde was degraded best, followed by acetone and toluene; the least degraded compound was heptane. The measurement of released CO2 revealed that 90% of degraded hexane was mineralised to CO2 and water while for a mixture of 4 VOCs, the level of mineralisation was 83%.

• Klíčová slova
• Gaseous pollutants, ISO 22197-2, Nanoparticulate films, P25, P90, Photocatalysis, TiO2,
• Publikační typ
• časopisecké články MeSH

Nanosized boron(III) oxide-doped titania was prepared by homogeneous hydrolysis of titanium oxo-sulfate with urea in aqueous solutions in the presence of amorphous boron. The prepared samples were annealing at 700 degrees C. The structure of as-prepared samples was characterized by X-ray powder diffraction (XRD) and selected area electron diffraction (SAED) and surface area (BET) and porosity determination (BJH). The morphology and microstructure characteristics were obtained by scanning electron microscopy (SEM) and high-resolution electron microscopy (HRTEM). The method of UV/vis diffuse reflectance spectroscopy was employed to estimate band gap energies of the boron-doped titania. The photoactivity of the prepared samples was assessed by the photocatalytic decomposition of Orange II dye in an aqueous slurry during irradiation at 365 and 400 nm wavelength. The prepared titania samples doped with boron(III) oxide showed better photocatalytic activity in comparison with the reference TiO(2) sample. These photocatalysts showed better photocatalytic performance under visible-light irradiation.

• Publikační typ
• časopisecké články MeSH
• práce podpořená grantem MeSH