The in situ coating of polymer substrate with polypyrrole, described herein with detailed know-how, represents a novel technique of surface functionalization. The choice of oxidizing agent and the polymerization time both affect the properties of the thin polypyrrole layer. The specific conductivity, free surface energy, thickness, topography, and FTIR spectra of polypyrrole layer were determined. The conductive coatings were further used to functionalize both isotropic and anisotropic electrospun polyurethane nanofibrous mats to show their applicability and study the bioactive effect of both the anisotropy and conductivity together. The morphology of composites was studied by means of atomic force microscopy and scanning electron microscopy. A complex cytocompatibility study was performed, including determining cytotoxicity by optical and fluorescence microscopy, the advanced qualification of cell morphology by cell-image analysis, and a study of stem cell behavior. The results clearly showed the significant impact of substrate modification on cells, especially on fibroblasts while the embryonic stem cells were less affected. This study shows not only the effective way to prepare a thin conducting layer based on polypyrrole but also demonstrates its importance for the fabrication of smart biomaterials.
- Klíčová slova
- Anisotropy, Coating, Conductivity, Image analysis, Stem cells,
- Publikační typ
- časopisecké články MeSH
Combining highly conducting one-dimensional nanostructures of polypyrrole with cellulose nanofibers (CNF) into flexible films with tailored electrical conductivity and mechanical properties presents a promising route towards the development of eco-friendly electromagnetic interference shielding devices. Herein, conducting films with a thickness of 140 μm were synthesized from polypyrrole nanotubes (PPy-NT) and CNF using two approaches, i.e., a new one-pot synthesis consisting of in situ polymerization of pyrrole in the presence of structure guiding agent and CNF, and a two-step synthesis, in which CNF and PPy-NT were physically blended. Films based on one-pot synthesis (PPy-NT/CNFin) exhibited higher conductivity than those processed by physical blending, which was further enhanced up to 14.51 S cm-1 after redoping using HCl post-treatment. PPy-NT/CNFin containing the lowest PPy-NT loading (40 wt%), thus the lowest conductivity (5.1 S cm-1), displayed the highest shielding effectiveness of -23.6 dB (>90 % attenuation), thanks to the good balance between its mechanical properties and electrical conductivity.
- Klíčová slova
- Cellulose nanofibers, Composite films, Electrical conductivity, Electromagnetic interference shielding, Polypyrrole nanotubes,
- Publikační typ
- časopisecké články MeSH
A sedimentation-stable magnetorheological (MR) polishing slurry on the basis of ferrofluid, iron particles, Al2O3, and clay nanofiller in the form of sepiolite intended for MR polishing has been designed, prepared, and its polishing efficiency verified. Added clay substantially improved sedimentation stability of the slurry, decreasing its sedimentation rate to a quarter of its original value (1.8 to 0.45 mg s-1) while otherwise maintaining its good abrasive properties. The magnetisation curve measurement proved that designed slurry is soft magnetic material with no hysteresis, and its further suitability for MR polishing was confirmed by its magnetorheology namely in the quadratically increased yield stress due to the effect of applied magnetic field (0 to 600 kA m-1). The efficiency of the MR polishing process was tested on the flat samples of injection-moulded polyamide and verified by surface roughness/3D texture measurement. The resulting new composition of the MR polishing slurry exhibits a long-term stable system with a wide application window in the MR polishing process.
- Klíčová slova
- 3D texture, clay, magnetorheology, polishing, sedimentation, slurry,
- MeSH
- jíl MeSH
- magnetismus MeSH
- nylony * MeSH
- železo * MeSH
- Publikační typ
- časopisecké články MeSH
- Názvy látek
- jíl MeSH
- magnesium trisilicate MeSH Prohlížeč
- nylony * MeSH
- železo * MeSH
Novel composite films combining biocompatible polysaccharides with conducting polyaniline (PANI) were prepared via the in-situ polymerization of aniline hydrochloride in the presence of sodium hyaluronate (SH) or chitosan (CH). The composite films possess very good cytocompatibility in terms of adhesion and proliferation of two lines of human induced pluripotent stem cells (hiPSC). Moreover, the cardiomyogenesis and even formation of beating clusters were successfully induced on the films. The proportion of formed cardiomyocytes demonstrated excellent properties of composites for tissue engineering of stimuli-responsive tissues. The testing also demonstrated antibacterial activity of the films against E. coli and PANI-SH was able to reduce bacterial growth from 2 × 105 to < 1 cfu cm-2. Physicochemical characterization revealed that the presence of polysaccharides did not notably influence conductivities of the composites being ∼1 and ∼2 S cm-1 for PANI-SH and PANI-CH respectively; however, in comparison with neat PANI, it modified their topography making the films smoother with mean surface roughness of 4 (PANI-SH) and 14 nm (PANI-CH). The combination of conductivity, antibacterial activity and mainly cytocompatibility with hiPSC opens wide application potential of these polysaccharide-based composites.
- Klíčová slova
- Conducting composites, Human induced pluripotent stem cells, Polyaniline, Polysacharides,
- MeSH
- aniliny chemie MeSH
- antibakteriální látky chemie farmakologie MeSH
- biokompatibilní materiály chemie farmakologie MeSH
- buněčná adheze účinky léků MeSH
- buněčné linie MeSH
- chitosan chemie MeSH
- elektrická vodivost MeSH
- Escherichia coli účinky léků MeSH
- indukované pluripotentní kmenové buňky účinky léků metabolismus MeSH
- kyselina hyaluronová chemie MeSH
- lidé MeSH
- nanokompozity chemie MeSH
- polymerizace MeSH
- povrchové vlastnosti MeSH
- proliferace buněk účinky léků MeSH
- Staphylococcus aureus účinky léků MeSH
- tkáňové inženýrství metody MeSH
- Check Tag
- lidé MeSH
- Publikační typ
- časopisecké články MeSH
- Názvy látek
- aniline MeSH Prohlížeč
- aniliny MeSH
- antibakteriální látky MeSH
- biokompatibilní materiály MeSH
- chitosan MeSH
- kyselina hyaluronová MeSH
- polyaniline MeSH Prohlížeč
The design of a unipole and a dual band F-shaped antenna was conducted to find the best parameters of prepared antenna. Antenna radiator part is fully made of polymer and nonmetal base composite. Thermoplastic polyurethane (PU) was chosen as a matrix and multi-wall carbon nanotubes (MWCNT) as an electrical conductive filler, which creates conductive network. The use of the composite for the antenna has the advantage in simple preparation through dip coating technique. Minor disadvantage is the usage of solvent for composite preparation. Composite structure was used for radiator part of antenna. The antenna operates in 2.45 and 5.18 GHz frequency bands. DC conductivity of our PU/MWCNT composite is about 160 S/m. With this material, a unipole and a dual band F antenna were realized on 2 mm thick polypropylene substrate. Both antenna designs were also simulated using finite integration technique in the frequency domain (FI-FD). Measurements and full wave simulations of S11 of the antenna showed good agreement between measurements and simulations. Except for S11, the gain and radiation pattern of the antennas were measured and simulated. Maximum gain of the designed unipole antenna is around -10.0 and -5.5 dBi for 2.45 and 5.18 GHz frequency bands, respectively. The manufactured antennas are intended for application in wearable electronics, which can be used to monitor various activities such as walking, sleeping, heart rate or food consumption.
- Klíčová slova
- carbon nanotubes, composite material, effective conductivity, effective permeability, effective permittivity, polymer antenna, wearable electronics,
- Publikační typ
- časopisecké články MeSH
Polypyrrole one-dimensional nanostructures (nanotubes, nanobelts and nanofibers) were prepared using three various dyes (Methyl Orange, Methylene Blue and Eriochrome Black T). Their high electrical conductivity (from 17.1 to 60.9 S cm-1), good thermal stability (in the range from 25 to 150 °C) and resistivity against ageing (half-time of electrical conductivity around 80 days and better) were used in preparation of lightweight and flexible composites with silicone for electromagnetic interference shielding in the C-band region (5.85-8.2 GHz). The nanostructures' morphology and chemical structure were characterized by scanning electron microscopy, Brunauer-Emmett-Teller specific surface measurement and attenuated total reflection Fourier-transform infrared spectroscopy. DC electrical conductivity was measured using the Van der Pauw method. Complex permittivity and AC electrical conductivity of respective silicone composites were calculated from the measured scattering parameters. The relationships between structure, electrical properties and shielding efficiency were studied. It was found that 2 mm-thick silicone composites of polypyrrole nanotubes and nanobelts shield almost 80% of incident radiation in the C-band at very low loading of conductive filler in the silicone (5% w/w). Resulting lightweight and flexible polypyrrole composites exhibit promising properties for shielding of electromagnetic interference in sensitive biological and electronic systems.
- Klíčová slova
- 1D nanostructures, conducting polymers, electromagnetic shielding, microwave region, thermal stability,
- MeSH
- azosloučeniny chemie MeSH
- elektromagnetické záření * MeSH
- methylenová modř chemie MeSH
- mikroskopie elektronová rastrovací MeSH
- nanostruktury chemie účinky záření ultrastruktura MeSH
- nanotrubičky chemie účinky záření ultrastruktura MeSH
- nanovlákna chemie účinky záření MeSH
- polymery chemie účinky záření MeSH
- pyrroly chemie účinky záření MeSH
- silikony chemie účinky záření MeSH
- Publikační typ
- časopisecké články MeSH
- Názvy látek
- azosloučeniny MeSH
- Eriochrome Black T MeSH Prohlížeč
- methyl orange MeSH Prohlížeč
- methylenová modř MeSH
- polymery MeSH
- polypyrrole MeSH Prohlížeč
- pyrroly MeSH
- silikony MeSH
This paper presents a methodology for accurately gauging the true plane wave shielding effectiveness of composite polymer materials via rectangular waveguides. Since the wave propagation of the waveguides is not in the form of plane wave patterns, it is necessary to post-process the S-parameters for the measured data of the waveguide lines to obtain such patterns and ascertain the effectiveness of true plane wave shielding. The authors propose two different methods to achieve this. The first applies simple renormalization of S-parameters, where reference impedance is changed from the value for the waveguide to that for free space, which ensures good accuracy of shielding effectiveness with a small degree of discontinuity across the range of frequencies. The other relies on rigorous extraction of the composite materials' effective permittivity and permeability ascertained from rectangular waveguides; afterward, plane wave shielding effectiveness is calculated analytically and gives very high accuracy. Both procedures assume the given samples are isotropic in character. We validated the accuracy of the methodologies by conducting tests on a set of synthetic samples of 2 mm thickness with unit permittivity and variable conductivity and on a dielectric material of known permittivity (FR4 laminate). The applicability of both methods was further proven by analyzing the isotropic composite materials, a process involving the use of iron particles embedded in a dielectric matrix. The synthetic samples and an FR4 material were tested to check the accuracy of the methods. Based on numerical studies and measurements, we concluded that materials with a shielding effectiveness of up to 25 dB could be measured at a maximum amplitude error of 1 dB to 3dB to a frequency of 18 GHz, depending on the relative permittivity of the material; hence, the first method was suitable for approximation purposes. For maximal accuracy, the second method typically demonstrated an amplitude error of below 0.5 dB to the same frequency across the entire range.
- Klíčová slova
- composite material, electromagnetic shielding, permeability, permittivity, waveguide,
- Publikační typ
- časopisecké články MeSH
The flexible supercapacitors (SCs) of the conventional sandwich-type structure have poor flexibility due to the large thickness of the final entire device. Herein, we have fabricated a highly flexible asymmetric SC using manganese dioxide (MnO₂) and reduced graphene oxide (RGO) nanosheet-piled hydrogel films and a novel bacterial cellulose (BC)-filled polyacrylic acid sodium salt-Na₂SO₄ (BC/PAAS-Na₂SO₄) neutral gel electrolyte. Apart from being environmentally friendly, this BC/PAAS-Na₂SO₄ gel electrolyte has high viscosity and a sticky property, which enables it to combine two electrodes together. Meanwhile, the intertangling of the filled BC in the gel electrolyte hinders the decrease of the viscosity with temperature, and forms a separator to prevent the two electrodes from short-circuiting. Using these materials, the total thickness of the fabricated device does not exceed 120 μm. This SC device demonstrates high flexibility, where bending and even rolling have no obvious effect on the electrochemical performance. In addition, owing to the asymmetric configuration, the cell voltage of this flexible SC has been extended to 1.8 V, and the energy density can reach up to 11.7 Wh kg-1 at the power density of 441 W kg-1. This SC also exhibits a good cycling stability, with a capacitance retention of 85.5% over 5000 cycles.
- Klíčová slova
- bacterial cellulose, flexible asymmetric supercapacitor, gel electrolyte, manganese dioxide, reduced graphene oxide, two-dimensional material,
- Publikační typ
- časopisecké články MeSH
The effect of ionic surfactants and manufacturing methods on the separation and distribution of multi-wall carbon nanotubes (CNTs) in a silicone matrix are investigated. The CNTs are dispersed in an aqueous solution of the anionic surfactant dodecylbenzene sulfonic acid (DBSA), the cationic surfactant cetyltrimethylammonium bromide (CTAB), and in a DBSA/CTAB surfactant mixture. Four types of CNT-based composites of various concentrations from 0 to 6 vol.% are prepared by simple mechanical mixing and sonication. The morphology, electrical and thermal conductivity of the CNT-based composites are analyzed. The incorporation of both neat and modified CNTs leads to an increase in electrical and thermal conductivity. The dependence of DC conductivity versus CNT concentration shows percolation behaviour with a percolation threshold of about 2 vol.% in composites with neat CNT. The modification of CNTs by DBSA increases the percolation threshold to 4 vol.% due to the isolation/separation of individual CNTs. This, in turn, results in a significant decrease in the complex permittivity of CNT–DBSA-based composites. In contrast to the percolation behaviour of DC conductivity, the concentration dependence of thermal conductivity exhibits a linear dependence, the thermal conductivity of composites with modified CNTs being lower than that of composites with neat CNTs. All these results provide evidence that the modification of CNTs by DBSA followed by sonication allows one to produce composites with high homogeneity.
- MeSH
- benzensulfonáty chemie MeSH
- cetrimoniové sloučeniny chemie MeSH
- cetrimonium MeSH
- elektrická vodivost * MeSH
- impedanční spektroskopie MeSH
- nanokompozity chemie ultrastruktura MeSH
- nanotrubičky uhlíkové chemie ultrastruktura MeSH
- povrchově aktivní látky chemie MeSH
- silikonové elastomery chemie MeSH
- tepelná vodivost * MeSH
- termogravimetrie MeSH
- vibrace ultrazvukové MeSH
- Publikační typ
- časopisecké články MeSH
- práce podpořená grantem MeSH
- Názvy látek
- benzensulfonáty MeSH
- cetrimoniové sloučeniny MeSH
- cetrimonium MeSH
- dodecylbenzenesulfonic acid MeSH Prohlížeč
- nanotrubičky uhlíkové MeSH
- povrchově aktivní látky MeSH
- silikonové elastomery MeSH
