This paper presents research aimed at laboratory experiments on static and cyclic fatigue testing of low-density polyethylene (LDPE) recovered from post-consumer waste in order to develop a recycled product exhibiting satisfactory mechanical and thermo-mechanical properties. The results of the cyclic fatigue tests set up to 80% of the maximum load in static tensile testing demonstrated satisfactory functionality of the recycled material developed by using the injection molding process. There was no significant change in the tensile strength under static and cyclic fatigue tests. Under cyclic loading, there was a quasi-static effect manifested by plastic deformation, and the displacement increased significantly. The static and cyclic tensile tests indicated improvement in the mechanical performance of the recycled LDPE as compared to the virgin material, owing to the high quality of the regranulates. Fourier Transform Infrared Spectroscopy (FTIR) was conducted to analyze the functional groups in virgin and recycled LDPE samples. The analysis showed no significant change in the transmittance spectra. The thermal degradation performance was also analyzed by Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA). The results were quite similar for both virgin and recycled LDPE.

• Klíčová slova
• Fourier transform infrared spectroscopy, cyclic fatigue, differential scanning calorimetry, dynamic mechanical analysis, injection molding technology, low-density polyethylene, mechanical properties, post-consumer waste, recycling, thermal degradation,
• Publikační typ
• časopisecké články MeSH

Bacterial cellulose (BC) presents significant promise as a biomaterial, boasting unique qualities such as exceptional cellulose purity, robust mechanical strength, heightened crystalline structure, and biodegradability. Several studies have highlighted specific effects, such as the impact of dehydration/rehydration on BC tensile strength, the influence of polymer treatment methods on mechanical properties, the correlation between microorganism type, drying method, and Young's modulus value, and the relationship between culture medium composition, pH, and crystallinity. Drying methods are crucial to the structure, performance, and application of BC films. Research findings indicate that the method used for drying can influence the mechanical properties of BC films, including parameters such as tensile strength, Young's modulus, and water absorption capacity, as well as the micromorphology, crystallinity, and thermal characteristics of the material. Their versatility makes them potential biomaterials applicable in various fields, including thermal and acoustic insulation, owing to their distinct thermal and mechanical attributes. This review delves into the thermal and mechanical behavior of bacterial cellulose aerogels, which are profoundly impacted by their drying mechanism.

• Klíčová slova
• bacterial cellulose hydrogel, drying methods, lyophilization, structure, thermal and mechanical behavior,
• Publikační typ
• časopisecké články MeSH
• přehledy MeSH

This paper presents a study conducted on prepregs manufactured by a novel method for the impregnation of a thermoplastic matrix. Different composite prepregs based on polypropylene and reinforced with natural fibers (e.g., basalt and jute fibers) were developed. The mechanical and dynamic mechanical properties were investigated. DMA tests were conducted at 1 Hz frequency and properties such as storage modulus and damping (tan δ) were evaluated. The overall mechanical properties of the basalt fiber composites were found to be superior to that of the jute fiber-based samples. Thermo-gravimetric analysis (TG/DTG) of the composite samples showed that the thermal degradation temperatures of the basalt-based composites shifted to higher temperature regions compared to the PP or jute fiber composites. The addition of basalt fiber considerably improved the thermal stability of the composite samples. Microscopic images of the tensile fractured composite samples illustrated better fiber-matrix interfacial interaction due to the novel technology of prepregs. Single-ply and 2-ply prepregs showed significantly superior mechanical, thermal, and thermo-dynamical performance compared to the control sample (pure PP). 2-Ply composites demonstrated higher modulus, tensile strength, and storage modulus due to the higher fiber volume fraction. Basalt-based samples showed a minimum weight loss of about 57% up to 700 °C in contrast to 96.05% weight loss in the jute-based samples and 98.4% in the case of pure PP. The heat resistance index (THRI) is more than twice for basalt compared to jute and PP. Furthermore, the superior thermal stability of basalt is reflected in its DSC curves, showing the highest endothermic peak. The technique of using the resin in the form of thermoplastic yarns offers cost effective and efficient alternatives for composite manufacturing.

• Klíčová slova
• differential scanning calorimetry, dynamic mechanical analysis, prepregs, tensile properties, thermal properties, thermoplastic, thermos-gravimetric analysis, weaving,
• Publikační typ
• časopisecké články MeSH

Nafion possesses many interesting properties such as a high ion-conductivity, hydrophilicity, and thermal and chemical stability that make this material highly suitable for many applications including fuel cells and various (bio-)chemical and physical sensors. However, the mechanical properties of a Nafion membrane that are known to be affected by the viscoplastic characteristics of the material itself have a strong impact on the performance of Nafion-based sensors. In this study, the mechanical properties of Nafion under the cyclic loading have been investigated in detail. After cyclic tensile loading (i.e., maximum elongation about 25% at a room temperature and relative humidity about 40%) a time-dependent recovery comes into play. This recovery process is also shown being strain-rate dependent. Our results reveal that the recovery behavior weakens after performing several stress-strain cycles. Present findings can be of a great importance in future design of various chemical and biological microsensors and nanosensors such as hydrogen or glucose ones.

• Klíčová slova
• Nafion, cyclic loading, mechanical properties, mechanical tests, viscoplastic properties,
• Publikační typ
• časopisecké články MeSH

Natural fibre as a reinforcing agent has been widely used in many industries in this era. However, the reinforcing agent devotes a better strength when embedded with a polymer matrix. Nevertheless, the characteristic of natural fibre and polymer matrix are in contrast, as natural fibre is hydrophilic, while polymer is hydrophobic in nature. Natural fibre is highly hydrophilic due to the presence of a hydroxyl group (-OH), while polymer matrix has an inherent hydrophobic characteristic which repels water. This issue has been fixed by modifying the natural fibre's surface using a chemical treatment combining an alkaline treatment and a silane coupling agent. This modifying process of natural fibre might reduce the attraction of water and moisture content and increase natural fibre surface roughness, which improves the interfacial bonding between these two phases. In this paper, the effect of alkaline and silane treatment has been proven by performing the mechanical test, Scanning Electron Micrograph (SEM), and Fourier Transform Infrared spectrometry (FTIR) to observe the surface structure. The chemical compositions and thermal properties of the composites have been obtained by performing Differential Scanning Calorimetry (DSC) and Thermogravimetric Analysis (TGA) tests. 1.0% silane treatment displayed better strength performance as compared to other composites, which was proven by performing Scanning Electron Micrograph (SEM). The assumption is that by enduring chemical treatment, kenaf fibre composites could develop high performance in industry applications.

• Klíčová slova
• Fused Deposition Modelling (FDM), fibre treatment, kenaf fibre, mechanical properties, thermal properties,
• Publikační typ
• časopisecké články MeSH

One of the solutions for overheating the interior in the summer without increasing energy consumption is the integration of phase change material (PCM) into interior plasters. However, adding PCM to plasters deteriorates their properties and thus their usability. The aim of this paper is to determine how the microencapsulated PCM affects the mechanical, thermal, and fire properties of plasters and how much PCM can be added to the plaster. Two sets of samples were prepared: in set S, part of the aggregate was replaced by PCM; and in set R, only PCM was added. The bulk density, flexural strength, compressive strength, tensile strength perpendicular to the surface, thermal conductivity coefficient, specific heat capacity, melting, and solidification temperatures and enthalpy were measured. A single-flame source fire test and a gross heat of combustion fire test were performed to determine the reaction to the fire class. The results show that with an increasing proportion of PCM, the strength of the samples of set R decreased more significantly than it did with the samples of set S. It was found that only up to about 10% PCM could be added to set R, while up to 30% PCM could be added to set S.

• Klíčová slova
• fire properties, gypsum, mechanical properties, phase change material, thermal properties,
• Publikační typ
• časopisecké články MeSH

Current research deals with thermoplastic polyamide (PA6)-based composites reinforced with basalt and Kevlar fabrics. Hybrid composites were developed by altering the stacking sequence of basalt and two kinds of Kevlar fabrics. Pure-basalt- and pure-Kevlar-based samples were also developed for comparison purposes. The developed samples were evaluated with respect to mechanical and thermomechanical properties. Mechanical tests, e.g., tensile, flexural, and impact strength, were conducted along with thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) to ascertain the load-bearing and high-temperature stability of the hybrid composite samples vis-à-vis pure-basalt- and Kevlar-based samples. Scanning electron microscopy (SEM) was carried out to study the nature of fracture and failure of the composite samples. The pure-basalt-based PA6 thermoplastic composites exhibited the best mechanical performance. Hybridization with basalt proved to be beneficial for improving the mechanical performance of the composites using Kevlar fabrics. However, a proper stacking sequence and density of Kevlar fabric has to be selected. The thermogravimetric analysis showed minimal weight loss for basalt-based composites. Furthermore, the thermal stability of the composites using Kevlar fabric was improved by hybridization with basalt fabric. The thermomechanical characteristics of hybrid composites may be altered by changing the stacking order of the reinforcements. Differential scanning calorimetry further established that the hybrid composites with alternate layers of basalt and Kevlar can improve the heat flow rate and enable survivability at extreme temperatures. Such novel hybrid composites can be used for high-load-bearing and high-temperature applications, e.g., defense, aerospace, automotives, and energy applications.

• Klíčová slova
• Kevlar, basalt, differential scanning calorimetry (DSC), hybrid composite, mechanical test, scanning electron microscopy (SEM), thermogravimetric analysis (TGA), thermoplastic,
• Publikační typ
• časopisecké články MeSH

This article deals with the influence of electron-beam radiation on the micro-mechanical, thermo-mechanical, and structural properties of selected polymers. In the search for the desired improvement of polymers, it is possible to use, inter alia, one particular possible modification-Namely, crosslinking-Which is a process during which macromolecular chains start to connect to each other and, thus, create the spatial network in the structure. In the course of the treatment of the ionizing radiation, two actions can occur: crosslinking and scission of macromolecules, or degradation. Both these processes run in parallel. Using the crosslinking technology, standard and technical polymers can acquire the more "expensive" high-tech polymeric material properties and, thus, replace these materials in many applications. The polymers that were tested were selected from across the whole spectra of thermoplastics, ranging from commodity polymers, technical polymers, as well as high-performance polymers. These polymers were irradiated by different doses of beta radiation (33, 66, 99, 132, 165, and 198 kGy). The micro-mechanical and thermo-mechanical properties of these polymers were measured. When considering the results, it is obvious that irradiation acts on each polymer differently but, always when the optimal dose was found, the mechanical properties increased by up to 36%. The changes of micro-mechanical and thermo-mechanical properties were confirmed by structural measurement when the change of the micro-hardness and modulus corresponded to the crystalline phase change as determined by X-ray and gel content.

• Klíčová slova
• TMA (thermo-mechanical analysis), X-ray, beta rays, crosslinking, gel content, micro-indentation,
• Publikační typ
• časopisecké články MeSH

This paper explores the influence of selected commercial plasticizers structure, which are based on esters of citric acid, on mechanical and thermal properties of Poly(3-hydroxybutyrate)/Poly(lactic acid)/Plasticizer biodegradable blends. These plasticizers were first tested with respect to their miscibility with Poly(3-hydroxybutyrate)/Poly(lactic acid) (PHB/PLA) blends using a kneading machine. PHB/PLA/plasticizer blends in the weight ratio (wt %) of 60/25/15 were then prepared by single screw and corotating meshing twin screw extruders in the form of filament for further three-dimensional (3D) printing. Mechanical, thermal properties, and shape stability (warping effect) of 3D printed products can be improved just by the addition of appropriate plasticizer to polymeric blend. The goal was to create new types of eco-friendly PHB/PLA/plasticizers blends and to highly improve the poor mechanical properties of neat PHB/PLA blends (with majority of PHB) by adding appropriate plasticizer. Mechanical properties of plasticized blends were then determined by the tensile test of 3D printed test samples (dogbones), as well as filaments. Measured elongation at break rapidly enhanced from 21% for neat non-plasticized PHB/PLA blends (reference) to 328% for best plasticized blends in the form of filament, and from 5% (reference) to 187% for plasticized blends in the form of printed dogbones. The plasticizing effect on blends was confirmed by Modulated Differential Scanning Calorimetry. The study of morphology was performed by the Scanning Electron Microscopy. Significant problem of plasticized blends used to be also plasticizer migration, therefore the diffusion of plasticizers from the blends after 15 days of exposition to 110 °C in the drying oven was investigated as their measured weight loss. Almost all of the used plasticizers showed meaningful positive softening effects, but the diffusion of plasticizers at 110 °C exposition was quite extensive. The determination of the degree of disintegration of selected plasticized blend when exposed to a laboratory-scale composting environment was executed to roughly check the "biodegradability".

• Klíčová slova
• 3D printing, biodegradable polymeric blends, mechanical properties, plasticizers, poly(hydroxybutyrate)/poly(lactic), thermal properties,
• Publikační typ
• časopisecké články MeSH

Nowadays, with the development of electromobility, the requirements not only for the mechanical properties but also for the thermal conductivity of castings are increasing. This paper investigates the influence of casting and heat treatment technology on the thermal diffusivity and thermal conductivity of an AlSi10MnMg alloy. The thermal diffusivity was monitored as a function of temperature in the range of 50-300 °C for the material cast by high-pressure die casting (HPDC) and also by gravity sand casting (GSC) and gravity die casting (GDC). This study also investigated the effect of the T5 heat treatment temperature (artificial ageing without prior solution treatment-HT200, HT300, and HT400) on the thermal conductivity of the material cast by different technologies. Experiments confirmed that the thermal diffusivity or thermal conductivity of the alloy depends on the casting technology. The slower the cooling rate of the casting, the higher the thermal conductivity value. For the alloy in the as-cast condition, the thermal conductivity at 50 °C is in the range of about 125 to 138 [W·m-1·K-1]. Regardless of the casting method, the thermal conductivity tends to increase with temperature (50-300 °C). Furthermore, a positive effect of heat treatment without prior solution treatment (HT200, HT300, and HT400) on the thermal conductivity was demonstrated. Regardless of the casting method of the samples, the thermal conductivity also increases with increasing heat treatment temperature. The results further showed that when artificial ageing is performed in industrial practice on castings to increase mechanical properties in the temperature range of 160-230 °C, this heat treatment has a positive effect on thermal conductivity.

• Klíčová slova
• aluminium alloy, casting, heat treatment, thermal conductivity, thermal diffusivity,
• Publikační typ
• časopisecké články MeSH