This work is focused on preparation of novel porous type of core-shell-structured microparticles based on polylactide (shell) and poly(vinyl alcohol) cross-linked with glutaric acid (GA) (core) prepared by water-in-oil-in-water solvent evaporation technique. The microparticle systems were used as delivery systems for immobilisation of model antibacterial agent - nisin. The effect of cross-linking and the initial amount of nisin on their morphology was investigated using scanning electron microscopy, BET analysis, zeta potential measurement and Fourier transform infra-red spectroscopy. Encapsulation efficiency and release profile of nisin from the microparticles were studied by high performance liquid chromatography. Antibacterial activity of the prepared systems was tested by dilution and spread plate technique. Results showed the microparticles in the size range of 9-16 μm in diameter with spherical multi-hollow core-shell structure. The presence of cross-linking agent GA influences the release profile of the peptide and has synergistic effect on Listeria monocytogenes growth reduction.
- MeSH
- antibakteriální látky aplikace a dávkování MeSH
- glutaráty chemie MeSH
- Listeria monocytogenes účinky léků MeSH
- mikroskopie elektronová rastrovací MeSH
- nisin aplikace a dávkování MeSH
- nosiče léků chemie MeSH
- polyestery chemie MeSH
- polyvinylalkohol chemie MeSH
- poréznost MeSH
- velikost částic MeSH
- Publikační typ
- časopisecké články MeSH
OBJECTIVE: An inhomogeneous irradiance distribution from a light-curing unit (LCU) can locally cause inhomogeneous curing with locally inadequately cured and/or over-cured areas causing e.g. monomer elution or internal shrinkage stresses, and thus reduce the lifetime of dental resin based composite (RBC) restorations. The aim of the study is to determine both the irradiance distribution of two light curing units (LCUs) and its influence on the local mechanical properties of a RBC. METHODS: Specimens of Arabesk TOP OA2 were irradiated for 5, 20, and 80s using a Bluephase® 20i LCU in the Low mode (666mW/cm(2)), in the Turbo mode (2222mW/cm(2)) and a Celalux® 2 (1264mW/cm(2)). The degree of conversion (DC) was determined with an ATR-FTIR. The Knoop micro-hardness (average of five specimens) was measured on the specimen surface after 24h of dark and dry storage at room temperature. RESULTS: The irradiance distribution affected the hardness distribution across the surface of the specimens. The hardness distribution corresponded well to the inhomogeneous irradiance distributions of the LCU. The highest reaction rates occurred after approximately 2s light exposure. A DC of 40% was reached after 3.6 or 5.7s, depending on the LCU. The inhomogeneous hardness distribution was still evident after 80s of light exposure. SIGNIFICANCE: The irradiance distribution from a LCU is reflected in the hardness distribution across the surface. Irradiance level of the LCU and light exposure time do not affect the pattern of the hardness distribution--only the hardness level. In areas of low irradiation this may result in inadequate resin polymerization, poor physical properties, and hence premature failure of the restorations as they are usually much smaller than the investigated specimens. It has to be stressed that inhomogeneous does not necessarily mean poor if in all areas of the restoration enough light intensity is introduced to achieve a high degree of cure.
- MeSH
- časové faktory MeSH
- povrchové vlastnosti MeSH
- radiační rozptyl * MeSH
- spektroskopie infračervená s Fourierovou transformací MeSH
- stomatologické polymerizační lampy * MeSH
- světlo * MeSH
- syntetické pryskyřice chemie MeSH
- testování materiálů MeSH
- tvrdost MeSH
- Publikační typ
- časopisecké články MeSH
- práce podpořená grantem MeSH
