X-ray photoelectron spectroscopy (XPS) Dotaz Zobrazit nápovědu
Thin-film growth of molecular systems is of interest for many applications, such as for instance organic electronics. In this study, we demonstrate how X-ray photoelectron spectroscopy (XPS) can be used to study the growth behavior of such molecular systems. In XPS, coverages are often calculated assuming a uniform thickness across a surface. This results in an error for rough films, and the magnitude of this error depends on the kinetic energy of the photoelectrons analyzed. We have used this kinetic-energy dependency to estimate the roughnesses of thin porphyrin films grown on rutile TiO2 (110). We used two different molecules: cobalt (II) monocarboxyphenyl-10,15,20-triphenylporphyrin (CoMCTPP), with carboxylic-acid anchor groups, and cobalt (II) tetraphenylporphyrin (CoTPP), without anchor groups. We find CoMCTPP to grow as rough films at room temperature across the studied coverage range, whereas for CoTPP the first two layers remain smooth and even; depositing additional CoTPP results in rough films. Although, XPS is not a common technique for measuring roughness, it is fast and provides information of both roughness and thickness in one measurement.
- Klíčová slova
- Growth, Porphyrin molecules, Thin films, X-ray photoelectron spectroscopy,
- Publikační typ
- časopisecké články MeSH
The adsorption of adenine on Cu(111) was studied by photoelectron and near edge x-ray absorption fine structure spectroscopy. Disordered molecular films were deposited by means of physical vapor deposition on the substrate at room temperature. Adenine chemisorbs on the Cu(111) surface with strong rehybridization of the molecular orbitals and the Cu 3d states. Annealing at 150 °C caused the desorption of weakly bonded molecules accompanied by formation of a short-range ordered molecular adlayer. The interface is characterized by the formation of new states in the valence band at 1.5, 7, and 9 eV. The present work complements and refines existing knowledge of adenine interaction with this surface. The coverage is not the main parameter that defines the adenine geometry and adsorption properties on Cu(111). Excess thermal energy can further rearrange the molecular adlayer and, independent of the initial coverage, the flat lying stable molecular adlayer is formed.
- MeSH
- adenin chemie MeSH
- fotoelektronová spektroskopie * MeSH
- měď chemie MeSH
- molekulární struktura MeSH
- povrchové vlastnosti MeSH
- rentgenová absorpční spektroskopie * MeSH
- Publikační typ
- časopisecké články MeSH
- Názvy látek
- adenin MeSH
- měď MeSH
For several years, scientists have been trying to understand the mechanisms that reduce the long-term stability of perovskite solar cells. In this work, we examined the effect of water and photon flux on the stability of CH3 NH3 PbI3 perovskite films and solar cells using in situ near-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS), field emission scanning electron microscopy (FESEM), and current density-voltage (J-V) characterization. The used amount of water vapor (up to 1 mbar) had a negligible impact on the perovskite film. The higher the photon flux, the more prominent were the changes in the NAP-XPS and FESEM data; also, a faster decline in power conversion efficiency (PCE) and a more substantial hysteresis in the J-V characteristics were observed. Based on our results, it can be concluded that the PCE decrease originates from the creation of Frenkel pair defects in the perovskite film under illumination. The stronger the illumination, the higher the number of Frenkel defects, leading to a faster PCE decline and more substantial hysteresis in the J-V sweeps.
Graphene on diamond has been attracting considerable attention due to the unique and highly beneficial features of this heterostructure for a range of electronic applications. Here, ultrahigh-vacuum X-ray photoelectron spectroscopy is used for in situ analysis of the temperature dependence of the Ni-assisted thermally induced graphitization process of intrinsic nanocrystalline diamond thin films (65 nm thickness, 50-80 nm grain size) on silicon wafer substrates. Three major stages of diamond film transformation are determined from XPS during the thermal annealing in the temperature range from 300 °C to 800 °C. Heating from 300 °C causes removal of oxygen; formation of the disordered carbon phase is observed at 400 °C; the disordered carbon progressively transforms to graphitic phase whereas the diamond phase disappears from the surface from 500 °C. In the well-controllable temperature regime between 600 °C and 700 °C, the nanocrystalline diamond thin film is mainly preserved, while graphitic layers form on the surface as the predominant carbon phase. Moreover, the graphitization is facilitated by a disordered carbon interlayer that inherently forms between diamond and graphitic layers by Ni catalyst. Thus, the process results in formation of a multilayer heterostructure on silicon substrate.
- Publikační typ
- časopisecké články MeSH
In the paper, the Scanning Electron Microscopy (SEM) with Energy Dispersive X-ray Spectroscopy (EDS) and X-ray Photoelectron Spectroscopy (XPS) results of the surface layer formed on pure titanium after plasma electrolytic oxidation (micro arc oxidation) at the voltage of 450 V are shown. As an electrolyte, the mixture of copper nitrate Cu(NO₃)₂ (10-600 g/L) in concentrated phosphoric acid H₃PO₄ (98 g/mol) was used. The thickness of the obtained porous surface layer equals about 10 μm, and it consists mainly of titanium phosphates and oxygen with embedded copper ions as a bactericidal agent. The maximum percent of copper in the PEO surface layer was equal to 12.2 ± 0.7 wt % (7.6 ± 0.5 at %), which is the best result that the authors obtained. The top surface layer of all obtained plasma electrolytic oxidation (PEO) coatings consisted most likely mainly of Ti₃(PO₄)₄∙nH₃PO₄ and Cu₃(PO₄)₂∙nH₃PO₄ with a small addition of CuP₂, CuO and Cu₂O.
We present a new technique for investigating complex model electrocatalysts by means of electrochemical in situ ambient-pressure X-ray photoelectron spectroscopy (AP-XPS). Using a specially designed miniature capillary device, we prepared a three-electrode electrochemical cell in a thin-layer configuration and analyzed the active electrode/electrolyte interface by using "tender" X-ray synchrotron radiation. We demonstrate the potential of this versatile method by investigating a complex model electrocatalyst. Specifically, we monitored the oxidation state of Pd nanoparticles supported on an ordered Co3O4(111) film on Ir(100) in an alkaline electrolyte under potential control. We found that the Pd oxide formed in the in situ experiment differs drastically from the one observed in an ex situ emersion experiment at similar potential. We attribute these differences to the decomposition of a labile palladium oxide/hydroxide species after emersion. Our experiment demonstrates the potential of our approach and the importance of electrochemical in situ AP-XPS for studying complex electrocatalytic interfaces.
- Publikační typ
- časopisecké články MeSH
Carbon K-edge resonant Auger spectra of gas-phase allene following excitation of the pre-edge 1s → π* transitions are presented and analysed with the support of EOM-CCSD/cc-pVTZ calculations. X-Ray absorption (XAS), X-ray photoelectron (XPS), valence band and non-resonant Auger spectra are also reanalysed with a series of computational approaches. The results presented demonstrate the importance of including nuclear ensemble effects for simulating X-ray observables and as an effective strategy for capturing Jahn-Teller effects in spectra.
- Publikační typ
- časopisecké články MeSH
Although the nitrous oxide belongs among three of the most contributing greenhouse gases to global warming, it is quite neglected by photocatalytic society. The g-C3N4 and WO3 composites were therefore tested for the photocatalytic decomposition of N2O for the first time. The pure photocatalysts were prepared by simple calcination of precursors, and the composites were prepared by mixing of suspension of pure components in water followed by calcination. The structural (X-ray diffraction, X-ray photoelectron spectroscopy, high-resolution transmission electron microscopy), textural (N2 physisorption), and optical properties (diffuse reflectance spectroscopy, photoluminescence spectroscopy, photoelectrochemical measurements) of all composites were correlated with photocatalytic activity. The experimental results and results from characterization techniques confirmed creation of Z-scheme in the WO3/g-C3N4 composites, which was confirmed by hydroxyl radicals' trapping measurements. The photocatalytic decomposition of N2O was carried out in the presence of UVA light (peak intensity at 365 nm) and the 1:2 WO3/g-C3N4 composite was the most active one, but the photocatalytic activity was just negligibly higher than that of pure WO3. This is caused by relatively weak interaction between WO3 and g-C3N4 which was revealed from XPS.
- Klíčová slova
- Heterojunction, N2O decomposition, OH trapping, Photocatalysis, WO3, g-C3N4,
- MeSH
- chemické modely MeSH
- difrakce rentgenového záření MeSH
- fotochemické procesy * MeSH
- fotoelektronová spektroskopie MeSH
- hydroxylový radikál MeSH
- katalýza MeSH
- oxid dusičitý chemie MeSH
- světlo MeSH
- transmisní elektronová mikroskopie MeSH
- wolfram chemie MeSH
- Publikační typ
- časopisecké články MeSH
- Názvy látek
- hydroxylový radikál MeSH
- oxid dusičitý MeSH
- wolfram MeSH
Radio frequency plasma is one of the means to modify the polymer surface namely in the activation of polypropylene membranes (PPM) with O2 plasma. Activated membranes were deposited with TiO2 nanoparticles by the dip coating method and the bare sample and modified sample (PPM5-TiO2) were irradiated by UV lamps for 20-120 min. Characterization techniques such as X-ray diffraction (XRD), Attenuated total reflection technique- Fourier transform infrared spectroscopy (ATR-FTIR), Thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS), Scanning electron microscope (SEM) and water contact angle (WCA) measurements were applied to study the alteration of ensuing membrane surface properties which shows the nanoparticles on the sample surface including the presence of Ti on PPM. The WCA decreased from 135° (PPM) to 90° (PPM5-TiO2) and after UV irradiation, the WCA of PPM5-TiO2 diminished from 90° to 40°.
- Klíčová slova
- O2 plasma, PP membrane, TiO2 nanoparticles, UV treatment, hydrophilicity,
- MeSH
- difrakce rentgenového záření MeSH
- fotoelektronová spektroskopie MeSH
- kyslík chemie MeSH
- membrány umělé * MeSH
- nanočástice chemie MeSH
- plazmové plyny chemie MeSH
- polypropyleny chemie MeSH
- smáčivost MeSH
- spektroskopie infračervená s Fourierovou transformací MeSH
- teplota MeSH
- termogravimetrie MeSH
- titan chemie MeSH
- voda chemie MeSH
- Publikační typ
- časopisecké články MeSH
- Názvy látek
- kyslík MeSH
- membrány umělé * MeSH
- plazmové plyny MeSH
- polypropyleny MeSH
- titan MeSH
- titanium dioxide MeSH Prohlížeč
- voda MeSH
The precise design of bioactive surfaces, essential for the advancement of many biomedical applications, depends on achieving control of the surface architecture as well as on the ability to attach bioreceptors to antifouling surfaces. Herein, we report a facile avenue toward hierarchically structured antifouling polymer brushes of oligo(ethylene glycol) methacrylates via surface-initiated atom transfer radical polymerization (SI-ATRP) presenting photoactive tetrazole moieties, which permitted their functionalization via nitrile imine-mediated tetrazole-ene cyclocloaddition (NITEC). A maleimide-functional ATRP initiator was photoclicked to the side chains of a brush enabling a subsequent polymerization of carboxybetaine acrylamide to generate a micropatterned graft-on-graft polymer architecture as evidenced by X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). Furthermore, the spatially resolved biofunctionalization of the tetrazole-presenting brushes was accessed by the photoligation of biotin-maleimide and subsequent binding of streptavidin. The functionalized brushes bearing streptavidin were able to resist the fouling from blood plasma (90% reduction with respect to bare gold). Moreover, they were employed to demonstrate a model biosensor by immobilization of a biotinylated antibody and subsequent capture of an antigen as monitored in real time by surface plasmon resonance.
- MeSH
- fotochemie MeSH
- fotoelektronová spektroskopie MeSH
- hmotnostní spektrometrie MeSH
- methakryláty chemie MeSH
- polyethylenglykoly chemie MeSH
- polymery chemie MeSH
- povrchové vlastnosti MeSH
- Publikační typ
- časopisecké články MeSH
- práce podpořená grantem MeSH
- Názvy látek
- methakryláty MeSH
- polyethylenglykoly MeSH
- polymery MeSH
