Nowadays, most of the newly developed active pharmaceutical ingredients (APIs) consist of cohesive particles with a mean particle size of <100μm, a wide particle size distribution (PSD) and a tendency to agglomerate, therefore they are difficult to handle in continuous manufacturing (CM) lines. The current paper focuses on the impact of various glidants on the bulk properties of difficult-to-handle APIs. Three challenging powders were included: two extremely cohesive APIs (acetaminophen micronized (APAPμ) and metoprolol tartrate (MPT)) which previously have shown processing issues during different stages of the continuous direct compression (CDC)-line and a spray dried placebo (SD) powder containing hydroxypropylmethyl cellulose (HPMC), known for its sub-optimal flow with a high specific surface area (SSA) and low density. Four flow-enhancing excipients were used: a hydrophilic (Aerosil® 200) and hydrophobic (Aerosil® R972) fumed silica grade, a mesoporous silica grade (Syloid® 244FP), and a calcium phosphate excipient (TRI-CAFOS® 200-7). The APIs and binary API/glidant blends (varied between 0.5-2.75 w/w%) were characterized for their bulk properties relevant for CDC. The results indicated that optimizing different bulk parameters (e.g., density, flow, compressibility..) of an API required varying weight percentages of the glidant (e.g., different surface area coverage (SAC)) depending on the APIs. Moreover, even at similar SAC, the impact of the glidant on the bulk characteristic of the APIs depended on the glidant type properties. While nano-sized silicon dioxide were effective for improving the flowability of a powder, other glidants (mesoporous silica and tricalcium phosphate (TCP)) showed also promise as alternatives. Additionally, an excess of glidant, referred to as oversilication, negatively impacted some bulk parameters, but other characteristics were unaffected. Finally, to determine the appropriate concentration of the different classes of glidants, SAC calculations, an understanding of the glidant's working mechanism, and knowledge about the API's characteristics (i.e., morphology, compressibility, flowability, aeration, density, and wall friction) are required. This study confirmed the necessity of including various material characterization techniques to assess the impact of glidants on the bulk characteristics of APIs.
- MeSH
- Hypromellose Derivatives * chemistry MeSH
- Chemistry, Pharmaceutical methods MeSH
- Calcium Phosphates * chemistry MeSH
- Hydrophobic and Hydrophilic Interactions MeSH
- Metoprolol * chemistry MeSH
- Bulk Drugs MeSH
- Silicon Dioxide chemistry MeSH
- Acetaminophen * chemistry MeSH
- Excipients * chemistry MeSH
- Powders * MeSH
- Drug Compounding methods MeSH
- Rheology * MeSH
- Particle Size * MeSH
- Publication type
- Journal Article MeSH
Atmospheric new particle formation (NPF) is a naturally occurring phenomenon, during which high concentrations of sub-10 nm particles are created through gas to particle conversion. The NPF is observed in multiple environments around the world. Although it has observable influence onto annual total and ultrafine particle number concentrations (PNC and UFP, respectively), only limited epidemiological studies have investigated whether these particles are associated with adverse health effects. One plausible reason for this limitation may be related to the absence of NPF identifiers available in UFP and PNC data sets. Until recently, the regional NPF events were usually identified manually from particle number size distribution contour plots. Identification of NPF across multi-annual and multiple station data sets remained a tedious task. In this work, we introduce a regional NPF identifier, created using an automated, machine learning based algorithm. The regional NPF event tag was created for 65 measurement sites globally, covering the period from 1996 to 2023. The discussed data set can be used in future studies related to regional NPF.
- Publication type
- Journal Article MeSH
This research paper presents a novel approach to the green synthesis of silver nanoparticles (AgNPs) using viticultural waste, allowing to obtain NP dispersions with distinct properties and morphologies (monodisperse and polydisperse AgNPs, referred to as mAgNPs and pAgNPs) and to compare their biological activities. Our synthesis method utilized the ethanolic extract of Vitis vinifera pruning residues, resulting in the production of mAgNPs and pAgNPs with average sizes of 12 ± 5 nm and 19 ± 14 nm, respectively. Both these AgNPs preparations demonstrated an exceptional stability in terms of size distribution, which was maintained for one year. Antimicrobial testing revealed that both types of AgNPs inhibited either the growth of planktonic cells or the metabolic activity of biofilm sessile cells in Gram-negative bacteria and yeasts. No comparable activity was found towards Gram-positives. Overall, pAgNPs exhibited a higher antimicrobial efficacy compared to their monodisperse counterparts, suggesting that their size and shape may provide a broader spectrum of interactions with target cells. Both AgNP preparations showed no cytotoxicity towards a human keratinocyte cell line. Furthermore, in vivo tests using a silkworm animal model indicated the biocompatibility of the phytosynthesized AgNPs, as they had no adverse effects on insect larvae viability. These findings emphasize the potential of targeted AgNPs synthesized from viticultural waste as environmentally friendly antimicrobial agents with minimal impact on higher organisms.
- MeSH
- Anti-Infective Agents pharmacology chemistry MeSH
- Biofilms drug effects MeSH
- Bombyx MeSH
- Cell Line MeSH
- Gram-Negative Bacteria drug effects MeSH
- Keratinocytes drug effects MeSH
- Metal Nanoparticles * chemistry MeSH
- Yeasts drug effects MeSH
- Larva drug effects MeSH
- Humans MeSH
- Microbial Sensitivity Tests * MeSH
- Plant Extracts pharmacology chemistry MeSH
- Silver * pharmacology chemistry metabolism MeSH
- Green Chemistry Technology MeSH
- Particle Size MeSH
- Cell Survival drug effects MeSH
- Vitis * chemistry MeSH
- Animals MeSH
- Check Tag
- Humans MeSH
- Animals MeSH
- Publication type
- Journal Article MeSH
Liposomal carrier systems have emerged as a promising technology for pulmonary drug delivery. This study focuses on two selected liposomal systems, namely, dipalmitoylphosphatidylcholine stabilized by phosphatidic acid and cholesterol (DPPC-PA-Chol) and dipalmitoylphosphatidylcholine stabilized by polyethylene glycol and cholesterol (DPPC-PEG-Chol). First, the research investigates the stability of these liposomal systems during the atomization process using different kinds of nebulizers (air-jet, vibrating mesh, and ultrasonic). The study further explores the aerodynamic particle size distribution of the aerosol generated by the nebulizers. The nebulizer that demonstrated optimal stability and particle size was selected for more detailed investigation, including Andersen cascade impactor measurements, an assessment of the influence of flow rate and breathing profiles on aerosol particle size, and an in vitro deposition study on a realistic replica of the upper airways. The most suitable combination of a nebulizer and liposomal system was DPPC-PA-Chol nebulized by a Pari LC Sprint Star in terms of stability and particle size. The influence of the inspiration flow rate on the particle size was not very strong but was not negligible either (decrease of Dv50 by 1.34 μm with the flow rate increase from 8 to 60 L/min). A similar effect was observed for realistic transient inhalation. According to the in vitro deposition measurement, approximately 90% and 70% of the aerosol penetrated downstream of the trachea using the stationary flow rate and the realistic breathing profile, respectively. These data provide an image of the potential applicability of liposomal carrier systems for nebulizer therapy. Regional lung drug deposition is patient-specific; therefore, deposition results might vary for different airway geometries. However, deposition measurement with realistic boundary conditions (airway geometry, breathing profile) brings a more realistic image of the drug delivery by the selected technology. Our results show how much data from cascade impactor testing or estimates from the fine fraction concept differ from those of a more realistic case.
- MeSH
- 1,2-Dipalmitoylphosphatidylcholine MeSH
- Aerosols MeSH
- Administration, Inhalation MeSH
- Bronchodilator Agents * MeSH
- Cholesterol MeSH
- Equipment Design MeSH
- Drug Delivery Systems MeSH
- Humans MeSH
- Liposomes MeSH
- Nebulizers and Vaporizers MeSH
- Trachea * MeSH
- Particle Size MeSH
- Check Tag
- Humans MeSH
- Publication type
- Journal Article MeSH
BACKGROUND: Targeted alpha therapy is one of the most powerful therapeutical modalities available in nuclear medicine. It's therapeutic potency is based on the nuclides that emit one or several alpha particles providing strong and highly localized therapeutic effects. However, some of these radionuclides, like e.g.223Ra or 225Ac decay in cascades, where the radioactive progeny originating from the consecutive alpha-decays may leave the original vector and cause unwanted irradiation of non-target organs. This progeny, even if partially retained in target tissues by internalization processes, typically do not follow the fate of originally targeted radiopharmaceutical and potentially spread over body following their own biodistribution. In this study we aimed to estimate 211Pb/211Bi progeny fate from the 223Ra surface-labelled TiO2 nanoparticles in vitro and the fate of 211Pb in vivo in a mice model. RESULTS: In vitro stability studies have shown significant differences between the release of the mother 223Ra and its progeny (211Pb, 211Bi) in all the biological matrices that have been tested. The lowest released activities were measured in saline, resulting in less than 5 % of released activity for all nuclides. Contrary to that, the highest released activity of 223Ra of up to 10 % within 48 h was observed in 5 % solution of albumin. The released activity of its progeny; the 211Pb and 211Bi was in the range of 20-40 % in this test medium. Significantly higher released activities of 211Pb and 211Bi compared to 223Ra by at least 10 % was observed in each biological medium, except saline, where no significant differences were observed. The in vivo biodistribution studies results in a mice model, show similar pattern, where it was found that even after accumulation of nanoparticles in target tissues, approximately 10 % of 211Pb is continuously released into the blood stream within 24 h, followed by its natural accumulation in kidneys. CONCLUSION: This study confirms our assumption that the progeny formed in a chain alpha decay of a certain nuclide, in this case the 223Ra, can be released from its original vector, leave the target tissue, relocate and could be deposited in non-target organs. We did not observe complete progeny wash-out from its original target tissues in our model. This indicates strong dependence of the progeny hot atom fate after its release from the original radiopharmaceutical preparation on multiple factors, like their internalization and retention in cells, cell membranes, extracellular matrices, protein binding, etc. We hypothesize, that also the primary tumour or metastasis size, their metabolic activity may significantly influence progeny fate in vivo, directly impacting the dose delivered to non-target tissues and organs. Therefore a bottom-up approach should be followed and detailed pre-/clinical studies on the release and biodistribution of radioactive progeny originating from the chain alpha emitters should be preferably performed.
- MeSH
- Mice MeSH
- Nanoparticles * MeSH
- Lead MeSH
- Radiopharmaceuticals * therapeutic use MeSH
- Radioisotopes therapeutic use MeSH
- Tissue Distribution MeSH
- Animals MeSH
- Check Tag
- Mice MeSH
- Animals MeSH
- Publication type
- Journal Article MeSH
The present work reviews the liquid antisolvent crystallization (LASC) to prepare the nanoparticle of pharmaceutical compounds to enhance their solubility, dissolution rate, and bioavailability. The application of ultrasound and additives is discussed to prepare the particles with narrow size distribution. The use of ionic liquid as an alternative to conventional organic solvent is presented. Herbal compounds, also known for low aqueous solubility and limited clinical application, have been crystalized by LASC and discussed here. The particle characteristics such as particle size and particle size distribution are interpreted in terms of supersaturation, nucleation, and growth phenomena. To overcome the disadvantage of batch crystallization, the scientific literature on continuous flow reactors is also reviewed. LASC in a microfluidic device is emerging as a promising technique. The different design of the microfluidic device and their application in LASC are discussed. The combination of the LASC technique with traditional techniques such as high-pressure homogenization and spray drying is presented. A comparison of product characteristics prepared by LASC and the supercritical CO2 antisolvent method is discussed to show that LASC is an attractive and inexpensive alternative for nanoparticle preparation. One of the major strengths of this paper is a discussion on less-explored applications of LASC in pharmaceutical research to attract the attention of future researchers.
Superparamagnetic iron oxide nanoparticles (SPION) with a "non-fouling" surface represent a versatile group of biocompatible nanomaterials valuable for medical diagnostics, including oncology. In our study we present a synthesis of novel maghemite (γ-Fe2O3) nanoparticles with positive and negative overall surface charge and their coating by copolymer P(HPMA-co-HAO) prepared by RAFT (reversible addition-fragmentation chain-transfer) copolymerization of N-(2-hydroxypropyl)methacrylamide (HPMA) with N-[2-(hydroxyamino)-2-oxo-ethyl]-2-methyl-prop-2-enamide (HAO). Coating was realized via hydroxamic acid groups of the HAO comonomer units with a strong affinity to maghemite. Dynamic light scattering (DLS) demonstrated high colloidal stability of the coated particles in a wide pH range, high ionic strength, and the presence of phosphate buffer (PBS) and serum albumin (BSE). Transmission electron microscopy (TEM) images show a narrow size distribution and spheroid shape. Alternative coatings were prepared by copolymerization of HPMA with methyl 2-(2-methylprop-2-enoylamino)acetate (MMA) and further post-polymerization modification with hydroxamic acid groups, carboxylic acid and primary-amino functionalities. Nevertheless, their colloidal stability was worse in comparison with P(HPMA-co-HAO). Additionally, P(HPMA-co-HAO)-coated nanoparticles were subjected to a bio-distribution study in mice. They were cleared from the blood stream by the liver relatively slowly, and their half-life in the liver depended on their charge; nevertheless, both cationic and anionic particles revealed a much shorter metabolic clearance rate than that of commercially available ferucarbotran.
- Publication type
- Journal Article MeSH
Milling affects not only particle size distributions but also other important granule quality attributes, such as API content and porosity, which can have a significant impact on the quality of the final drug form. The ability to understand and predict the effects of milling conditions on these attributes is crucial. A hybrid population balance model (PBM) was developed to model the Comil, which was validated using experimental results with an R2 of above 0.9. This presented model is dependent on the process conditions, material properties and equipment geometry, such as the classification screen size. In order to incorporate the effects of different quality attributes in the model physics, the dimensionality of the PBM was increased to account for changes in API content and porosity, which also produced predictions for these attributes in the results. Additionally, a breakage mode probability kernel was used to introduce dynamic breakage modes by predicting the probability of attrition and impact mode, which are dependent on the process conditions and feed properties at each timestep.
- MeSH
- Technology, Pharmaceutical * methods MeSH
- Porosity MeSH
- Drug Compounding methods MeSH
- Particle Size MeSH
- Publication type
- Journal Article MeSH
Long-acting injectable formulations represent a rapidly emerging category of drug delivery systems that offer several advantages compared to orally administered medicines. Rather than having to frequently swallow tablets, the medication is administered to the patient by intramuscular or subcutaneous injection of a nanoparticle suspension that forms a local depot from which the drug is steadily released over a period of several weeks or months. The benefits of this approach include improved medication compliance, reduced fluctuations of drug plasma level, or the suppression of gastrointestinal tract irritation. The mechanism of drug release from injectable depot systems is complex, and there is a lack of models that would enable quantitative parametrisation of the process. In this work, an experimental and computational study of drug release from a long-acting injectable depot system is reported. A population balance model of prodrug dissolution from asuspension with specific particle size distribution has been coupled with the kinetics of prodrug hydrolysis to its parent drug and validated using in vitro experimental data obtained from an accelerated reactive dissolution test. Using the developed model, it is possible to predict the sensitivity of drug release profiles to the initial concentration and particle size distribution of the prodrug suspension, and subsequently simulate various drug dosing scenarios. Parametric analysis of the system has identified the boundaries of reaction- and dissolution-limited drug release regimes, and the conditions for the existence of a quasi-steady state. This knowledge is crucial for the rational design of drug formulations in terms of particle size distribution, concentration and intended duration of drug release.
- MeSH
- Antipsychotic Agents * MeSH
- Injections, Intramuscular MeSH
- Delayed-Action Preparations MeSH
- Humans MeSH
- Prodrugs * MeSH
- Solubility MeSH
- Suspensions MeSH
- Drug Liberation MeSH
- Check Tag
- Humans MeSH
- Publication type
- Journal Article MeSH
Raman micro-spectroscopy technique offers a combination of relatively high spatial resolution with identification of components or mixtures of components in different sample areas, e.g. on the surface or the cross-section of a sample. This study is focused on the analysis of the tablets from pharmaceutical development with different technological parameters: (1) the manufacturing technology, (2) the particle size of the input API (active pharmaceutical ingredient) and (3) the quantitative composition of the individual excipients. These three mentioned parameters represent the most frequently solved problems in the field of reverse engineering in pharmacy. The investigation aims to distinguish tablets with the above-described technological parameters with limited subjective steps by Raman microscopy. Furthermore, non-subjective methods of Raman data analysis using advanced statistical analysis have been proposed, namely Principal Component Analysis, Soft Independent Modelling of Class Analogy and Linear Discriminant Analysis. The methods successfully distinguished and identified even very small differences in the analysed tablets within our study and provided objective statistic evaluation of Raman maps. The information on component and particle size distribution including their small differences, which is the critical parameter in the development of the original and generic products, was obtained due to combination of these methods. Even though each of these chemometric methods evaluates the data set from a different perspective, their mutual application on the problem of Raman maps evaluation confirmed and specified results on level that would be unattainable with the use of only one them.
- MeSH
- Chemometrics MeSH
- Pharmacy * MeSH
- Pharmaceutical Preparations * MeSH
- Excipients MeSH
- Spectrum Analysis, Raman MeSH
- Tablets MeSH
- Publication type
- Journal Article MeSH
